Isuzu NPR 2008 Скачать руководство пользователя страница 90 | Manualshive

Страница: 90 / 192

Isuzu NPR 2008 Скачать руководство пользователя страница 90

3-1

SECTION 3

IN CASE OF EMERGENCY

HAZARD WARNING LIGHT FLASHER

Use the hazard warning light flasher to warn other drivers any time

your vehicle becomes a traffic hazard, day or night.

Avoid stopping on the roadway, if possible.
Turn on the hazard warning flashers by pushing in the switch located

on the right-hand side of the instrument panel.

The flasher will work with the engine control switch either “ON” or

“OFF” and the key removed. Right and left turn signal indicators should
flash together when the hazard flasher is turned on.

The individual turn signals do not work when the hazard flasher is

turned on.

To turn off the flasher, push the switch again.

EMERGENCY STARTING YOUR VEHICLE

DUE TO A DISCHARGED BATTERY

If your vehicle will not start due to discharged batteries, it can often

be started by using energy from another battery—a procedure called
“jump starting”.

This vehicle has a 12-volt starting system and a negative ground

electrical system. Make sure that the other vehicle also has a 12-volt
starting system, and that it is the negative (–) terminal which is
grounded (attached to the engine block, or frame rail). Its operator’s
manual may give you that information. Do not try to jump start if you
are unsure of the other vehicle’s voltage or ground (or if the other
vehicle’s voltage and ground are different from your vehicle).

Connect the positive cable from the good battery to either of the

positive terminals on the discharged batteries.

55702_Sec03_'08 08.2.12 9:47 AM Page 1

«
...
88
89
90
91
92
...
»

Содержание NPR 2008

































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды