manualshive.com logo in svg

Isuzu NPR 2008, Руководство пользователя

Поделиться
Скачать
Isuzu NPR 2008 Скачать руководство пользователя страница 145

5-36

BRAKE SYSTEM

For the most effective braking and for maximum life from brake

system components, follow these suggestions:

•

Keep any obstructions from interfering with brake pedal travel. 

•

Keep tires properly inflated. Improperly inflated tires can reduce the
efficiency of the brakes.

Follow the recommendations for brake checks in the Maintenance

Schedule. Refer to “Brake System” in Section 2 for details on brake
system operation. Refer to the explanation of ABS in page 2-37.

RADIATOR COOLING FAN AND

GOVERNED SPEED

CAUTION: Increasing the governed speed of the engine or the fan
speed (by changing the fan drive ratio) may cause the engine’s
radiator cooling fan to fatigue, and then suddenly break apart while
rotating, possibly causing personal injury to anyone standing
nearby in addition to equipment damage. If it is felt the governed
speed must be changed, contact your dealer for information.

CAUTION: Winter fronts or grille covers are not to be used. Radiator
shutters may cause the engine’s radiator cooling fan to fatigue from
the alternate unloading and loading of the blades as each passes
through the area masked by the cover, then the unmasked area.
After the fan has been fatigued, it may suddenly break apart while
rotating, possibly causing personal injury to anyone standing
nearby, and equipment damage.

RADIATOR GRILLE COVERS

AIR CLEANER/FLAME ARRESTOR

CAUTION: The air cleaner also functions as a flame arrestor in the
event of engine backfire. The air cleaner should be installed at all
times unless its removal is necessary for repair or maintenance.
To help reduce the risk of personal injury or death and/or property
damage, be sure that no one is near the engine compartment
before starting the engine with the air cleaner removed. If engine
backfire occurs with the air cleaner removed, there could be a
burst of flame and possibly other fire in the engine compartment.

 55702_Sec05-2_'08  08.2.12 9:51 AM  Page 36

Содержание NPR 2008

































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды