manualshive.com logo in svg

Isuzu N Series 2008, Руководство пользователя, Страница: 34 / 580

Поделиться
Скачать
Isuzu N Series 2008 Скачать руководство пользователя страница 34

2-4

IMPORTANT INFORMATION

Misuse - 

The warranty does not cover damaged caused by:

•  Misuse or abuse of the vehicle including but not limited to racing, overloading, etc., 

or neglect.

•  Where component life is reduced due to application or environment – mining, 

logging, off-road, road-sweeper, tipper, towing, refuse, motor-home, agitator, crane, 

change of vehicle category, high centre of gravity, etc.

•  Operation of the vehicle after it is known to be defective.
•  Failure to carry out proper maintenance service in accordance with prescribed 

service intervals as set out in the maintenance schedule.

•  Failure of the vehicle, engine or of any component due to contamination and/or use 

of incorrect types and grades of fuel, oil, coolant or lubricants.

•  Alteration or modification of the vehicle by any party not authorised by IAL.
•  Failure to mount body/equipment in accordance with IAL recommendations.
•  Any fault caused by fitment of bodies and/or body mountings that do not conform to 

the IAL Body Builders Guide. This document is available on request from IAL.

•  The fitting of parts or accessories not approved by IAL or conforming to IAL’s 

specifications.
•  Cosmetic or surface corrosion resulting from scratches, stone chips, etc.
•  Any work carried out on the vehicle by someone other than an authorised Isuzu tuck 

dealer or authorised service dealer.

•  Deterioration due to normal use, exposure, wear and tear.
•  Operating the vehicle in circumstances where the prescribed engine hour’s service 

interval has been exceeded without proper maintenance causing excessive engine 

wear.

Excluded from Vehicle Warranty 

Defects in tyres (warranted by their manufacturer), batteries (warranted for 12 months), 

wheel alignments, brake and clutch linings, and any items that require replacement as 

part of normal vehicle maintenance. 

IAL warrants IAL approved Parts and Accessories ("Parts" and "Accessories") for the 

periods and on the conditions set out below. The warranty covers the correction, during 

the relevant warranty period, of defects in any such Parts and Accessories, by repair or 

at IAL’s option by replacement.

Accessories installed to the new vehicle

IAL approved Accessories installed by an Isuzu dealer or IAL authorised service dealer 

to the new vehicle, at the time of purchase, are covered by the vehicle warranty.

Parts and Accessories Warranty

2008N_sec02_print2.indd   4

15/09/2008   10:36:17 AM

Содержание N Series 2008





































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов