Invacare Platinum IRC5LXO2AW Скачать руководство пользователя страница 36

Страница: 36 / 84

SECTION 7—COMPRESSOR

Platinum

Oxygen

Part No 1118396

FIGURE 7.1

Replacing Compressor Assembly for 5 Liter Models

Replacing Compressor Assembly - 9 Liter Models

1. Turn power Off (O) and unplug the unit.

2. Remove the cabinet. Refer to Removing Cabinet on page 25.

3. Loosen clamps and disconnect intake hose and compressor output hose from

compressor assembly.

4. Remove compressor wires from wire clamps and tie-wraps. Disconnect motor

connector from the main harness connector.

5. Remove protective boot on capacitor.

6. Disconnect capacitor wires from the top of the capacitor.

NOTE: Re-use the protective boot if the replacement parts DO NOT provide one.

7. Remove the two mounting screws that secure the compressor restraint bracket and

remove the bracket.

8. Tilt compressor assembly toward front of unit and lift out.

9. Reverse STEPS 3-8 to install new compressor assembly.

10. Run unit and inspect for leaks. Refer to Leak Test on page 71.

11. If no leaks detected, turn power Off (O) and unplug the unit.

12. Reinstall cabinet. Refer to Removing Cabinet on page 25.

Compressors

Intake Hose

Mounting

Screws

Compressor

Restraint Bracket

Grommet

Wire Clamps or

Tie-wraps

Capacitor

Compressor

Output Hose

Содержание Platinum IRC5LXO2AW





















































































Результаты поиска

Содержание Platinum IRC5LXO2AW

Отзывы:

Похожие инструкции для Platinum IRC5LXO2AW

Бренды по названию

Популярные бренды

Invacare Platinum IRC5LXO2AW, Руководство по обслуживанию

Результаты поиска

Содержание Platinum IRC5LXO2AW

Отзывы:

Похожие инструкции для Platinum IRC5LXO2AW

Бренды по названию

Популярные бренды