Invacare Platinum IRC5LXO2AW Скачать руководство пользователя страница 47

Страница: 47 / 84

SECTION 12—HEAT EXCHANGER

SECTION 12—HEAT EXCHANGER

Replacing Heat Exchanger

NOTE: Refer to Recycling Information following local governing ordinances and recycling plans
regarding disposal of the concentrator or components.

Platinum 5 Models

DANGER

To prevent electrical shock, ALWAYS disconnect concentrator from electrical

outlet before servicing.

1. Turn power Off (O) and unplug the unit.

2. Remove cabinet. Refer to Removing Cabinet on page 25.

CAUTION

Use care not to deform heat exchanger when installing, removing or cleaning.

3. Remove compressor assembly. Refer to Replacing Compressor Assembly for 5 Liter

Models on page 35.

4. Loosen hose clamp and separate heat exchanger output fitting from hose elbow.

5. Remove heat exchanger from the soundbox assembly.

6. Reverse STEPS 3-6 to install new heat exchanger assembly.

7. Run unit and inspect for leaks. Refer to Leak Test on page 71.

8. If no leaks detected, turn power Off (O) and unplug the unit.

9. Reinstall cabinet. Refer to Removing Cabinet on page 25.

Содержание Platinum IRC5LXO2AW





















































































Результаты поиска

Содержание Platinum IRC5LXO2AW

Отзывы:

Похожие инструкции для Platinum IRC5LXO2AW

Бренды по названию

Популярные бренды

Invacare Platinum IRC5LXO2AW, Руководство по обслуживанию

Результаты поиска

Содержание Platinum IRC5LXO2AW

Отзывы:

Похожие инструкции для Platinum IRC5LXO2AW

Бренды по названию

Популярные бренды