Invacare Platinum IRC5LXO2AW Скачать руководство пользователя страница 60

Страница: 60 / 84

SECTION 20—4-WAY VALVE

SECTION 20— 4-WAY VALVE

NOTE: Refer to Recycling Information following local governing ordinances and recycling plans
regarding disposal of the concentrator or components.

DANGER

To prevent electrical shock, ALWAYS disconnect concentrator from electrical

outlet before servicing.

Replacing 4-Way Valve

1. Turn power Off (O) and unplug the unit.

2. Remove cabinet. Refer to Removing Cabinet on page 25.

3. Remove control panel. Refer to Removing Control Panel on page 50.

4. Remove the four mounting screws that secure the 4-way valve to the manifold

assembly.

NOTE: Ensure the manifold gasket is in place on 4-way valve before installing.

5. Position new

4-way valve onto manifold assembly and loosely install mounting

screws through 4-way valve and into manifold assembly.

CAUTION

Torque sequence and specification MUST be adhered to or possible damage to the

4-way valve could result.

6. Tighten mounting screws in the sequence described below.

7. Pre-torque the mounting screws to 1.1 N-M ± 0.2 N-M (10 in-lbs ± 2 in-lbs) using the

torque sequence.

8. The mounting screws can be now be torqued to 2.5 N-M ± 0.2 N-M (22 in-lbs ± 2 in-lbs)

in the same sequence.

CAUTION

This is a maintenance free valve. Opening the valve will void any and all warranties

applicable to the valve.

Содержание Platinum IRC5LXO2AW





















































































Результаты поиска

Содержание Platinum IRC5LXO2AW

Отзывы:

Похожие инструкции для Platinum IRC5LXO2AW

Бренды по названию

Популярные бренды

Invacare Platinum IRC5LXO2AW, Руководство по обслуживанию

Результаты поиска

Содержание Platinum IRC5LXO2AW

Отзывы:

Похожие инструкции для Platinum IRC5LXO2AW

Бренды по названию

Популярные бренды