Invacare Platinum IRC5LXO2AW Скачать руководство пользователя страница 14

Страница: 14 / 84

SECTION 1—SAFETY

CAUTION

Risk of Damage
To prevent damage from liquid ingress:
If the concentrator is not working properly, if it has been dropped or damaged, or

dropped into water, call equipment supplier/qualified technician for examination

and repair.
NEVER drop or insert any object or liquid into any opening.
For Indoor Use ONLY.

WARNING

Risk of Injury
It is very important to select the prescribed level of oxygen flow. To avoid injury

from oxygen deprivation:
DO NOT increase or decrease the flow unless a change has been prescribed by your

physician or therapist.
ALWAYS confirm prescribed dose before administering to patient and monitor on

a frequent basis.

WARNING

Risk of damage
Shorter periods of operation may reduce maximum product life. For optimum

performance:
The concentrator should be on and running for a minimum of 30 minutes at a time.

Содержание Platinum IRC5LXO2AW





















































































Результаты поиска

Содержание Platinum IRC5LXO2AW

Отзывы:

Похожие инструкции для Platinum IRC5LXO2AW

Бренды по названию

Популярные бренды

Invacare Platinum IRC5LXO2AW, Руководство по обслуживанию

Результаты поиска

Содержание Platinum IRC5LXO2AW

Отзывы:

Похожие инструкции для Platinum IRC5LXO2AW

Бренды по названию

Популярные бренды