Invacare Platinum IRC5LXO2AW Скачать руководство пользователя страница 26

Страница: 26 / 84

SECTION 6—PREVENTIVE MAINTENANCE

Platinum

Oxygen

Part No 1118396

SECTION 6—PREVENTIVE
MAINTENANCE

NOTE: Refer to Recycling Information following local governing ordinances and recycling plans

regarding disposal of the concentrator or components.

DANGER

To prevent electrical shock, ALWAYS disconnect concentrator from electrical

outlet before servicing.

WARNING

Risk of Injury or Damage
Invacare oxygen concentrators are specifically designed to minimize routine

preventive maintenance. To prevent injury or damage:
Only professionals of the healthcare field or persons fully conversant with this

process such as factory trained personnel should perform preventive maintenance

or performance adjustments on the oxygen concentrator, except for tasks

described in this manual.
Users should contact your dealer or Invacare for service.

NOTE: At a minimum, preventive maintenance MUST be performed according to the

maintenance record guidelines. In places with high dust or soot levels, maintenance may need to

be performed more often. Refer to Troubleshooting on page 20 for plugged filter symptoms and to

Preventive Maintenance Record Invacare Platinum Oxygen Concentrator on page 34.

Cleaning the Cabinet Filter

NOTE: There are two cabinet filters, one located on each side of the cabinet.

1. Remove each filter and clean as needed.

NOTE: Environmental conditions that may require more frequent cleaning of the filters include

but are not limited to: high dust, smoking, air pollutants, etc.

2. Clean the cabinet filters with a vacuum cleaner or wash in warm soapy water and rinse

thoroughly.

3. Dry the filters thoroughly before reinstallation.

CAUTION

DO NOT operate the concentrator without the filters installed.

Содержание Platinum IRC5LXO2AW





















































































Результаты поиска

Содержание Platinum IRC5LXO2AW

Отзывы:

Похожие инструкции для Platinum IRC5LXO2AW

Бренды по названию

Популярные бренды

Invacare Platinum IRC5LXO2AW, Руководство по обслуживанию

Результаты поиска

Содержание Platinum IRC5LXO2AW

Отзывы:

Похожие инструкции для Platinum IRC5LXO2AW

Бренды по названию

Популярные бренды