Invacare Platinum IRC5LXO2AW Скачать руководство пользователя страница 20

Страница: 20 / 84

SECTION 4—TROUBLESHOOTING

Platinum

Oxygen

Part No 1118396

SECTION 4—TROUBLESHOOTING

SYMPTOM

PROBABLE CAUSE

SOLUTION

Normal Operation

Internal Status Indicators:

RED: Off

GREEN: Off

Unit plugged in, power switch on.

Single beep on start up.

No Problems

System Okay

Power Loss

Internal Status Indicators:

RED: Off

GREEN: Off

Unit unplugged, power switch on,

alarm off.

No Problems

Battery Free Circuit drained. Plug in cord and turn
power switch ON

to recharge.

Power Loss

Internal Status Indicators:

RED: Off

GREEN: Off

Unit plugged in, power switch, alarm

off, battery Free circuit drained.

No power at outlet

Check electrical outlet with a table lamp or

voltmeter set on the appropriate VAC scale. If

outlet isn't working, check protective device in

home's electrical panel or consult an electrician.

Also ensure that unit is properly plugged in. DO

NOT use extension cords. Move to another outlet

or circuit.

Power cord:

a. Frayed

b. Broken or damaged spade

c. Spade connector from power

cord loose or disconnected

(inside back of unit)

a. Reattach cord.

b. Replace power cord connectors on plug.

c. Reattach connector.

On/Off

switch

a. Disconnected wire
b. Faulty switch

Check all electrical connections to the On/Off

switch for any disconnected wires.

If the concentrator does not come on at all and

wiring is intact, color code and remove wires one

at a time. Remove and replace with new one.

Transfer wires from old switch to new switch one

at a time to the matching contact.

Circuit breaker tripped

Reset breaker

NOTE: Breaker may trip to safeguard concentrator

during a power surge.

If breaker trips IMMEDIATELY, there is a probable

short in the unit. Check for pinched or charred

wires. If the breaker does not trip, run unit for

approximately two hours. The circuit breaker

should be less than ten ohms. If breaker trips again,

there is an internal problem.

P.C. board

a. P.C. board damaged

b. Loose or damaged connector

a. Replace

P.C. Board. Refer to Replacing P.C.

Board on page 54.

b. Repair or replace connector. Refer to

Replacing P.C. Board on page 54.

Internal Power

Loss SensO

Internal Status Indicators:

RED: Off

GREEN: Off

Alarm may or may not be on.

Control Panel Indicators:

RED: Off

YELLOW: Off

GREEN: Off

Fan operates, Compressor not

operating.

Transformer assembly

a. Faulty

b. Connector loose or

disconnected

c. Faulty wiring

a. Replace. Refer to Replacing Transformer

Assembly on page 56.

b. Reattach connector.
c. Replace transformer assembly. Refer to

Replacing Transformer Assembly on
page 56.

P.C. board faulty

Replace P.C. board. Refer to Replacing P.C. Board

on page 54.

( )

(I /O)

Содержание Platinum IRC5LXO2AW





















































































Результаты поиска

Содержание Platinum IRC5LXO2AW

Отзывы:

Похожие инструкции для Platinum IRC5LXO2AW

Бренды по названию

Популярные бренды

Invacare Platinum IRC5LXO2AW, Руководство по обслуживанию

Результаты поиска

Содержание Platinum IRC5LXO2AW

Отзывы:

Похожие инструкции для Platinum IRC5LXO2AW

Бренды по названию

Популярные бренды