background image

14 / 14 

 

P/N 466-5519 • REV 0.01 • 24MAY19 

FCC Compliance 

This device complies with Part 15 of the FCC Rules.  

Operation is subject to the following two conditions: (1) This 

device may not cause harmful interference, and (2) This 

device must accept any interference received, including 

interference that may cause undesired operation. 

This equipment has been tested and found to comply with 

the limits for Class B Digital Device, pursuant to Part 15 of 

the FCC Rules. These limits are designed to provide 

reasonable protection against harmful interference in a 

residential installation. This equipment generates and can 

radiate radio frequency energy and, if not installed and used 

in accordance with the instructions, may cause harmful 

interference to radio communications. However, there is no 

guarantee that interference will not occur in a particular 

installation. If this equipment does cause harmful 

interference to radio or television reception, which can be 

determined by turning the equipment off and on, the user is 

encouraged to try to correct the interference by one or more 

of the following measures. 

x

 

Reorient or relocate the receiving antenna 

x

 

Increase the separation between the equipment and 

receiver 

x

 

Connect the equipment into an outlet on a circuit 

different from that to which the receiver is connected 

x

 

Consult the dealer or an experienced radio/TV 

technician for help 

Any changes or modifications not expressly approved by the 

party responsible for compliance could void the user’s 

authority to operate the equipment. 

This device complies with Industry Canada license-exempt 

RSS standard(s). Operation is subject to the following two 

conditions: (1) this device may not cause interference, and 

(2) this device must accept any interference, including 

interference that may cause undesired operation of the 

device. 

Le présent appareil est conforme aux CNR d'Industrie 

Canada applicables aux appareils radio exempts de licence. 

L'exploitation est autorisée aux deux conditions suivantes : 

(1) l'appareil ne doit pas produire de brouillage, et (2) 

l'utilisateur de l'appareil doit accepter tout brouillage 

radioélectrique subi, même si le brouillage est susceptible 

d'en compromettre le fonctionnement. 

Содержание IS-ZW-TSTAT-500















Отзывы: