P/N 466-5519 REV 0.01 • 24MAY19
9 / 14
Table 1:
Advance Settings continued
Aux Heat
Enable*
Range: Y or N
Default: Y
Enables the Auxiliary Heat operation.
Typically, the Aux Heat will be heat-strips in a Heat Pump
system
Aux heat control is wired to the W1 terminal.
Note*:
Heat pump systems only.
2
nd
Stage Heat
Enable
Range: Y or N
Default: N
Enables the 2
nd
Stage Heat operation
2
nd
Stage Cool
Enable
Range: Y or N
Default: N
Enables the 2
nd
Stage Cool operation
Minimum Run
Time
Range: 1- 9
Minutes
Default: 3
Sets the Minimum Run Time (MRT) delay before a
heating/cooling cycle can turn off.
Sets heating/cooling cycle time. Prevents rapid on/off
cycling.
Minimum Off
Time
Range: 5-9
Minutes
Default: 5
Sets the Minimum Off Time (MOT) delay before another
heating/cooling cycle can begin. Provides compressor
short cycle protection. “
WAIT
” is displayed on screen
when active.
Heat Setpoint
Max
Range: 30°F to
109°F (0°C-
43°C)
Default: 90°F
(32°C)
Sets the maximum heating setpoint value. Will not ramp
or accept setpoints higher than this maximum.
Cool Setpoint
Min
Range: 33°F to
112°F (2°C-
45°C)
Default: 60°F
(15°C)
Sets the minimum cooling setpoint value. Will not ramp or
accept setpoints lower than this minimum.
Heat Blower Off
Delay
Range: 0-90
seconds
Default: 0 (off)
Sets the system blower delay off time after a heat call
ends (fan purge).
Cool Blower Off
Delay
Range: 0-90
seconds
Default: 0 (off)
Sets the system blower delay off time after a cool call
ends (fan purge).
Heat - Cool
Delta
Range: 3° - 15°
Default: 3°F
(1°C)
Sets the minimum separation between heating and
cooling setpoints.
Table 1: Advance Settings continued
Setpoint Push
x
Attempts to lower the cooling setpoint below the
heating setpoint will PUSH the heating setpoint down
to maintain the heat/cool delta separation.
x
Attempts to set the heating setpoint above the cooling
setpoint will PUSH the cooling setpoint up to maintain
the setpoint heat/cool delta separation.
Heating Stage 1
On Threshold
Range: 1° to 6°
Default: 1°
Sets the delta from setpoint that stage 1 heating starts.
Heating Stage 1
Off Threshold
Range: 0° to 5°
Default: 0°
Sets the delta from setpoint that stage 1 heating stops.
Stage 1 turns off at se Delta Stage 1.
Heating Stage 2
On Threshold
Range: 2° to 7°
Default: 2
Sets the delta from setpoint that stage 2 heating starts.
Heating Stage 2
Off Threshold
Range: 0° to 6°
Default: 0°
Sets the delta from setpoint that stage 2 heating stops.
Stage 2 turns off at se Delta Stage 2.
Aux Heat On
Threshold
Range: 3° to 8°
Default: 3°
Sets the delta from setpoint that stage 3 heating starts.
Aux Heat Off
Threshold
Range: 0° to 7°
Default: 0°
Sets the delta from setpoint that stage 3 heating stops.
Stage 3 turns off at se Delta Stage 3.
Cooling Stage 1
On Threshold
Range: 1° to 7°
Default: 1°
Sets the delta from setpoint that stage 1 cooling starts.
Cooling Stage 1
Off Threshold
Range: 0° to 6°
Default: 0°
Sets the delta from setpoint that stage 1 cooling stops.
Stage 1 turns off at setpoint - Delta Stage 1
Cooling Stage 2
On Threshold
Range: 2° to 8°
Default: 2°
Sets the delta from setpoint that stage 2 cooling starts.
Cooling Stage 2
Off Threshold
Range: 0° to 7°
Default: 0°
Sets the delta from setpoint that stage 2 cooling stops.
Stage 2 turns off at setpoint - Delta Stage 2.
Restore
Defaults
Range: Yes, No
Default: No
Restores all settings to factory defaults.
Press Yes to restore defaults
Press No to exit and not restore defaults
