background image

© 01/01/19 UTC Fire & Security. All rights reserved. 

1 / 14 

P/N 466-5519 • REV 0.01 • 24MAY19 

24VAC or Battery Powered Z-Wave Thermostat 
Installation/User Guide 

Content

Description ........................................................................................ 1

Battery Powered Operation ............................................................... 1

Installation Steps ............................................................................... 2

Remove old thermostat ..................................................................... 2

Heat Pump HVAC Systems Wiring ................................................... 3

Mount the thermostat ........................................................................ 3

Standard Gas/Electric HVAC System Wiring .................................... 5

Heat Pump HVAC System Wiring ..................................................... 6

Thermostat Setup: Configure for HVAC System ............................... 7

Changing the HVAC System Setup .................................................. 7

Menu Options .................................................................................... 7

Advanced System Settings Menu ..................................................... 8

Advanced Settings ............................................................................ 8

Operation ........................................................................................ 10

Backlight and Button Operation ...................................................... 10

Thermostat Backlight Display.......................................................... 10

Setpoint Change ............................................................................. 11

Fan Modes ...................................................................................... 11

Thermostat Menu Mode .................................................................. 12

Menu Mode Options ........................................................................ 12

Thermostat Operation ..................................................................... 13

Minimum Run Time (MRT) .............................................................. 13

Minimum off Time (MOT) ................................................................ 13

Z-Wave

®

 Operation ......................................................................... 13

FCC Compliance ............................................................................. 14

Contact Information 

For contact information, see

www.utcfireandsecurity.com

or

www.interlogix.com. 

For technical support, toll-free: 888.437.3287 / 855.286.8889 

in the US including Alaska, Hawaii, Puerto Rico, and 

Canada.  

Outside toll-free area, contact your dealer. 

© 2019 UTC Fire & Security Americas Corporation, Inc. 

Interlogix is part of UTC Climate Controls & Security, a unit 

of United Technologies Corporation.  

All rights reserved. 

Safety Information 

WARNING: CHOKING 

HAZARD. 

The product accessory bag 

contains items that could be choking hazards. Please 

keep away from small children. 

AVERTISSEMENT: 

Le sachet de produits accessoires contient des 

éléments qui pourrait présenter un danger 

d’étouffement. Veuillez garder hors de la 

portée des jeunes enfants. 

Description 

This thermostat is compatible with most HVAC systems, 

including the following: 

x

 

24VAC systems   

Note:

  Requires both the 24VAC R and C (“common”) wires unless 

battery powered. 

x

 

Standard gas/oil/electric heating systems   

™

  1 stage heating and cooling 

™

  2 stage heating and cooling 

x

 

Heat Pump systems: 

™

  1 stage heating and cooling 

™

  2 stage heating and cooling 

™

  2

nd

 or 3

rd

 stage Auxiliary heating (heat strips)  

Warning! 

Do

NOT

 use for line voltage controls 

(120/240VAC)

The thermostat can either be powered by batteries or 

24VAC.

Battery Powered Operation 

The thermostat can be powered by four AA Alkaline 

batteries. The thermostat will operate for approximately two 

years on four AA Alkaline batteries depending on the 

frequency of user operations and backlight operation. 

Always use alkaline batteries and replace all four at the 

same time with 

NEW

 batteries. 

Содержание IS-ZW-TSTAT-500















Отзывы: