Intel 80C196NU Скачать руководство пользователя страница 435 | Manualshive

Страница: 435 / 471

Intel 80C196NU Скачать руководство пользователя страница 435

8XC196NP, 80C196NU USER’S MANUAL

C-44

SP_CON

SP_CON

Address:

Reset State:

1FBBH

00H

The serial port control (SP_CON) register selects the communications mode and enables or disables
the receiver, parity checking, and nine-bit data transmission. For the 80C196NU, it also enables or
disables the divide-by-two prescaler.

7

0

8XC196NP

—

—

PAR

TB8

REN

PEN

M1

M0

7

0

80C196NU

—

PRS

PAR

TB8

REN

PEN

M1

M0

Bit

Number

Bit

Mnemonic

Function

7

—

Reserved; for compatibility with future devices, write zero to this bit.

6

†

PRS

Prescale

This bit enables the divide-by-two prescaler.

0 = disable the prescaler
1 = enable the prescaler

5

PAR

Parity Selection Bit

Selects even or odd parity.

0 = even parity
1 = odd parity

4

TB8

Transmit Ninth Data Bit

This is the ninth data bit that will be transmitted in mode 2 or 3. This bit
is cleared after each transmission, so it must be set before SBUF_TX is
written. When SP_CON.2 is set, this bit takes on the even parity value.

3

REN

Receive Enable

Setting this bit enables the receiver function of the RXD pin. When this
bit is set, a high-to-low transition on the pin starts a reception in mode 1,
2, or 3. In mode 0, this bit must be clear for transmission to begin and
must be set for reception to begin. Clearing this bit stops a reception in
progress and inhibits further receptions.

2

PEN

Parity Enable

In modes 1 and 3, setting this bit enables the parity function. This bit
must be cleared if mode 2 is used. When this bit is set, TB8 takes the
parity value on transmissions. With parity enabled, SP_STATUS.7
becomes the receive parity error bit.

1:0

M1:0

Mode Selection

These bits select the communications mode.

M1

M0

0

0

mode 0

0

1

mode 1

1

0

mode 2

1

1

mode 3

†

This bit is reserved on the 8XC196NP. For compatibility with future devices, write zero to this bit.

«
...
433
434
435
436
437
...
»

Содержание 80C196NU
























































































































































































































































































































































































































































































Отзывы:

Нет отзывов