INSYS WLAN bridge Скачать руководство пользователя | Manualshive

Страница: 46 / 50

background image

40

Command Overview INSYS WLAN serial

Command Description

ATS4=

Character for line feed – LF

ATS4=n

n=0...127

Determination of the character as ASCII code

n=10 Default

setting

The setting is

not

stored with AT&W in the permanent memory.

ATS5=

Character for backspace – BS

ATS5=n

n=0...127

Determination of the character as ASCII code

n=8

Default

setting

The setting is

not

stored with AT&W in the permanent memory.

ATS8=

Set waiting period for block formation
Sets the waiting time until a block is sent via the network. The unit is in 1/1000 seconds
(1 ms). The time starts to run as soon as a character is received. As soon as no data is
received from the serial interface during the period set in S8, a data packet is sent. Small
values in S8 lead to faster transmission of short messages, but increase the number of
packets and therefore the load on the network side. Large packets in S8 lead to a delay of
small data packets.

ATS8=n

n=2..255

Waiting period in milliseconds (corresponds to 2ms ... 255
ms)

n=50

50 ms (default)

The setting is stored in the permanent memory with

AT&W

.

ATS12=

Pre and post run time for escape sequence
Minimum pre and post run time when sending the escape sequence („+++“)

ATS12=n

n=2...255

Time in units of 1/10 seconds

n=10

Default setting 1 second

The setting is stored in the permanent memory with AT&W.

ATSn

?

Query S-registry

n = 2,3,4,5,8,12 Query of the according registry

Access to other S-registries will not lead to errors, but also has no effect. When reading
non-implemented S-registries the value „0“ is returned.

AT*S

Set baud rate

AT*S

sets the baud rate at the serial interface. The following baud rates are supported:

AT*S1

300

baud

AT*S2

600

baud

AT*S3

1,200

baud

AT*S4

2,400

baud

AT*S5

4.800

baud

AT*S6

9,600

baud

AT*S7

19,200

baud

(default)

AT*S8

38,400

baud

AT*S9

57,600

baud

AT*S10

115,200

baud

AT&S

DSR behavior

AT&S0

DSR is always active (default)

AT&S1

DSR follows DCD, e.g. DSR is only active for existing connections

version 1.01 / 10.04

«
...
44
45
46
47
48
...
»

Содержание WLAN bridge



















































Отзывы:

Нет отзывов

Похожие инструкции для WLAN bridge

Бренд: 4RF Страницы: 7

ARM Cortex-A9 MPCore

Бренд: Dave Embedded Systems Страницы: 67

Бренд: F5 Страницы: 2

Бренд: F5 Страницы: 90

Бренд: F5 Страницы: 47

Бренд: Palm Страницы: 4

Бренд: Accuphase Страницы: 2

Бренд: ADTRAN Страницы: 2

AMB-VDX3H1 Series

Бренд: Acrosser Technology Страницы: 4

Бренд: Idis Страницы: 86

Бренд: Paradyne Страницы: 20

Бренд: Paradyne Страницы: 2

Бренд: RAK Страницы: 30

Бренд: Juniper Страницы: 7

Бренд: addlink Страницы: 9

1394 Dual-Port CardBus

Бренд: SIIG Страницы: 8

2000 IDU Series

Бренд: EMS Страницы: 52

DL-DVI-Vision-IP Series

Бренд: G&D Страницы: 228

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды