INSYS WLAN bridge Скачать руководство пользователя

Страница: 41 / 50

Command Overview INSYS WLAN serial

Command Description

AT#AUT

Set authorization
Explicit authentication at the AccessPoint before the data exchange

AT#AUT

Shared Key off (default)

AT#AUT

Shared Key on

The setting

AT#AUT

is immediately stored in the permanent memory (independent from

the command

AT&W

). The setting will only take effect with Reboot (

AT#RBT

AT&C

DCD behavior

AT&C0

DCD always on

AT&C1

DCD only on with existing connection (default)

AT#CHAN

Radio channel for adhoc mode

In adhoc mode, all involved modules must be set to the same channel.

AT#CHAN=n

Possible channel settings for Europe: n=1..14

In infrastructure mode the channel is assigned by the AccessPoint.

ATD

Dial remote terminal

The remote terminal is specified in the format IP number: Port. If no port is specified, the
own port number (set with

AT#PORT

) is also used for the remote terminal.

Optionally, it is possible to specify information regarding the necessary protocol (

ATDT

for TCP/IP or

ATDU

for UDP/IP), before the remote terminal is specified.

Example:

ATDT192.168.100.111:1234

dials port “1234” of the IP address 192.168.100.111 .

Protocol: TCP/IP.

ATDT192.168.100.111:1234

dials port “1234” of the IP address 192.168.100.111 .

Protocol: UDP/IP.

AT&D

Behavior with DTR drop

When the DTR line is deactivated during an existing connection, the function set through

AT&D

is executed.

AT&D0

Ignore DTR drop (for operation at modules which do not serve the DTR line).

AT&D2

A DTR drop causes the module to terminate the connection (default).

AT&D3

A DTR drop caused the module to terminate the connection and perform a
reset.

AT#DTC

Idle connection control (Data Transmit Controller)
The data transmit controller causes an unused connection to terminate automatically. If
no data is sent within the preset time, the connection is terminated.

AT#DTC=n

n in units of seconds

The maximum value is a timeout value of 2550 seconds (

AT#DTC=255

). The data

transmit controller can be switched off by setting the time to „0“ (

AT#DTC=0

). This is also

the default setting.

ATE

Echo

ATE0

Switches the echo of the entered command in command mode off

ATE1

Switches the echo on (default)

version 1.01 / 10.04

Содержание WLAN bridge



















































Результаты поиска

Содержание WLAN bridge

Отзывы:

Похожие инструкции для WLAN bridge

Бренды по названию

Популярные бренды

INSYS WLAN bridge, Руководство по эксплуатации

Результаты поиска

Содержание WLAN bridge

Отзывы:

Похожие инструкции для WLAN bridge

Бренды по названию

Популярные бренды