INSYS WLAN bridge Скачать руководство пользователя страница 42

Страница: 42 / 50

Command Overview INSYS WLAN serial

Command Description

AT&F

Load factory settings

Factory settings (defaults) are loaded.
By entering the command sequence

AT&F&W

, the module can be returned to the factory

settings (excluding the network settings).
All settings, which can be stored using

AT&W,

are affected by

AT&W

(not the network

settings, see also

AT&W

). However, not all settings that were saved using

AT&W

are

changed, only the currently active settings.

AT#GW

Set gateway address

AT#GW

sets the address of the standard gateway. This setting is used by remote IP

addresses, which can only be accessed by routers, not directly.
IP packets, which cannot be sent to the local network (defined by

AT#IP

and

AT#NM

), are

sent using the address set by

AT#GW

for forwarding.

AT#GW

is used in connection with

AT#NM

to establish a connection via a router. If a router

is used,

AT#GW

and

AT#NM

must be set to enable a data connection via the router.

The default setting is

AT#GW

=192.168.1.1

The setting

AT#GW

is immediately stored in the permanent memory (independent from

the command

AT&W

). The setting will only take effect with Reboot (

AT#RBT

The IP address, the gateway and the network mask must be coordinated in the local
network segment.
.

ATH

Dummy command

Command with an optional parameter without effect implemented for compatibility to
the modem – response “OK”.

The device does not support any online command mode.

ATI

Display of the module identification

ATI0

displays the device type („

WLAN 802.11b

“)

ATI3

displays the version number and the date when the software was created

ATI4

displays an ID string and the version number

AT*I

Querying the Alarm Input

Response:

Input is connected to GND and therefore activated

Input is open and therefore not activated

AT#IP

Set own IP address

AT#IP

sets the own IP address of the device, e.g.

AT#IP

=192.168.1.1

The default setting is

AT#IP

=192.168.1.160.

The setting

AT#IP

is immediately stored in the permanent memory (independent from

the command

AT&W

). The setting will only take effect with Reboot (

AT#RBT

IP address, gateway and network mask must be coordinated in the local network
segment.

version 1.01 / 10.04

Содержание WLAN bridge



















































Результаты поиска

Содержание WLAN bridge

Отзывы:

Бренды по названию

Популярные бренды

INSYS WLAN bridge, Руководство по эксплуатации

Результаты поиска

Содержание WLAN bridge

Отзывы:

Бренды по названию

Популярные бренды