INSYS WLAN bridge Скачать руководство пользователя страница 44

Страница: 44 / 50

Command Overview INSYS WLAN serial

Command Description

AT#PING

Send PING

AT#PINGa.b.c.d

sends an echo request (PING) to a remote terminal (similar to the

standard TCP/IP program). If an echo is received within a timeout period of 2 seconds,
the required time is displayed.

AT#PING

is used to check if an IP number can be reached. If

AT#PING

fails, no

connection can be established to the specified IP number.

The reason could be a wrong configuration or a firewall between the two network
subscribers.

AT#PORT

Set local port number

AT#PORT

sets the local port number to the value n (1..65535).

For automatic call acceptance, the local port number is used as the port number to which
the module “listens”.

The default setting is

AT#PORT

=1234

The setting

AT#PORT

is immediately stored in the permanent memory (independent

from the command

AT&W

). The setting will only take effect with Reboot (

AT#RBT

AT#PTY

Set port type

Determination of the WLAN architecture

AT#PTY

= 0

Adhoc (peer-to-peer)

AT#PTY

= 1

Infrastructure (Connection to AccessPoint – default)

The setting

AT#PTY

is immediately stored in the permanent memory (independent from

the command

AT&W

). The setting will only take effect with Reboot (

AT#RBT

ATQ

Quiet control

This command switches the sending of messages from the device via the serial interface
on or off.

ATQ0

Send messages to PC (default)

ATQ1

Don’t send messages to PC

AT#QUIET

Suppress switch-on message

AT#QUIET=0

shows the switch-on message during the cold start (default)

AT#QUIET=1

suppresses the switch-on message of the device

The setting of

AT#QUIET

is stored with

AT&W

in the fail-safe module memory of the

device.

AT&R

Polarity of the CTS control line
for controlling a RS485 driver (see also

AT&K8

). The CTS signal is set to active or inactive

when the device receives data at the serial interface:

AT&R0

CTS signal inactive

AT&R1

CTS signal active (default)

version 1.01 / 10.04

Содержание WLAN bridge



















































Результаты поиска

Содержание WLAN bridge

Отзывы:

Бренды по названию

Популярные бренды

INSYS WLAN bridge, Руководство по эксплуатации

Результаты поиска

Содержание WLAN bridge

Отзывы:

Бренды по названию

Популярные бренды