background image

200R204-000

Innovx FastSwitch Ethernet Switch

1-1

Issue 2

Installation and Operation Manual

Chapter 1: 

Introduction &

Specifications

Product Overview

The Innovx FastSwitch provides fast ethernet connectivity 
within the carrier’s internal network, allowing efficient and 
secure management of LAN-attached equipment. As part of 
the GDC SpectraComm family of products, FastSwitch 
offers the high reliability required in enterprise 
environments. FastSwitch can be deployed as a replacement 
to legacy hubs or in new installations where fast ethernet 
switching is desired.

Innovx FastSwitch cost-effectively increases network 
performance by reducing the collision domain, thereby 
easing congestion problems on existing shared-hub network 
traffic. In addition, FastSwitch eliminates unnecessary 
network traffic and delivers dedicated bandwidth for each 
port. FastSwitch also provides ethernet security features that 
enhance the security of the network. 

This manual describes both models of the Innovx FastSwitch 
device: the FastSwitch 9-Port card and the FastSwitch 18-
Port card. Both cards operate in the same manner, except 
where noted.

FastSwitch 9-Port Ethernet Switch

The FastSwitch 9-Port is a single-width, 7-inch by 9.5-inch 
(178 mm by 241 mm) printed circuit card that provides eight 
RJ45 ports at the Front Panel and one RJ45 port at the shelf 
rear panel. The Innovx TwinPak shelf can hold up to two 
FastSwitch 9-Port cards; the Innovx 1000 enclosure holds a 
single card. For higher density applications, the Innovx 
MultiPak enclosure holds 10 cards and the Innovx HD shelf 
can hold up to 16 cards.

FastSwitch 18-Port Ethernet Switch

The FastSwitch 18-Port is a double-width, 7-inch by 9.5-
inch (178 mm by 241 mm) printed circuit card that provides 
16 RJ45 ports at the front Panel and two RJ45 ports at the 
shelf rear panel. The Innovx MultiPak holds up to five cards 
and the Innovx HD shelf hold up to eight cards; multiple 
shelves increment port density.

FastSwitch

9-Port

8

7

6

5

4

3

2

1

9

ON

FastSwitch

18-Port

8

7

6

5

4

3

2

1

17

16

15

15

13

12

11

10

9

ON

18

Содержание FastSwitch































































Отзывы: