background image

 

Manual LightDriver 5.0 EN 

17

 

 

13.09.2018 V2.0 | innoflyer, weissensteinstrasse 81, 4500 solothurn | www.innoflyer.ch 

Recycling  

Electrical components shall not be thrown away with domestic 
waste; they must be disposed of in an appropriate and 
environmentally safe manner!  
Please comply with national and regional waste disposal 
regulations. Electronic waste shall be sorted in keeping with the 
provided disposal systems. 

Warranty 

The warranty in accordance with the following provisions is 2 years, unless 
expressly agreed otherwise in writing. 
 
The warranty period starts from the date of delivery. In case of failure to comply 
with our operating or maintenance instructions, alterations, the replacement of 
parts or the use of consumables that do not comply with the original 
specifications, the warranty will not apply as long as the defect can be traced 
back to this. This also applies if the defect can be traced back to improper use, 
storage and manipulation of the devices, third-party intervention or a fall. Minor 
deviations from the guaranteed characteristics of the goods do not trigger 
warranty rights.  
 
Liability for normal use and parts subject to wear and tear is excluded. 
 
In case of a defect of the purchased item for which raible eflugtechnik is 
responsible, raible eflugtechnik will be entitled to subsequent fulfillment 
(corrective action and replacement delivery). Should raible eflugtechnik be 
unable to rectify the defect within a suitable period, the contracting party will 
have recourse to the legal institutions of the Swiss Code of Obligations.  
 
We are liable for our own faults and those of our legal representatives and 
employees only as far as the fault is intentional or due to gross negligence. This 
does not apply to lack of assured properties.  
 
In case of commercial use of raible eflugtechnik products and services, in 
keeping with the Product Liability Act, no liability is accepted. 

 

 

Содержание LightDriver 5.0



















Отзывы: