Ingenico iCT2XX Скачать руководство пользователя страница 30

Страница: 30 / 147

SKYZER TECHNOLOGIES

PAGE 30 OF 147

INGENICO ICT2XX PTS2018 PAYMARK OPERATING MANUAL

Version 1.00

9.0

PABX?
1A
or
1W

Press

ENTER

to bypass if no PABX prefix is required.

This parameter specifies the PABX numbers that the terminal dials to access an
outside line.

Note:

The terminal pauses for 1 second after dialling if a control character

‘A’

inserted or to pauses for couple of seconds after dialling if a control character

‘W’

inserted after the PABX number. To insert a control character

‘A’

or ‘W’

, press the

corresponding number key and then the

FUNC

key.

To remove a PABX number from the PABX field, press

and then press

FUNC

key

until space is displayed followed by

ENTER

10.0

HOST PHONE NO?
08797

This parameter specifies the phone number of Paymark network to dial to. By
default, the host phone number is set as

08797

. Press

ENTER

NOTE: If the merchant has the Toll Bar on the site, then key in this phone
number 1797 to obtain connectivity to Paymark network.

11.0

USE DNS Y/N
1-YES 2-NO

Press the corresponding number key and press

ENTER

to set for DNS or IP

Option 1

–

to allow the terminal to use Paymark DNS address.

Option 1 is

selected by default

12.0

IP Primary

HOST DNS

direct.paymark.co.nz

This parameter specifies the Paymark Primary DNS address. By default, it is set to

direct.paymark.co.nz

. Press

ENTER

13.0

IP Secondary

Host DNS

direct2.paymark.co.n

This parameter specifies the Paymark Secondary DNS address. By default, it is set to

direct2.paymark.co.nz

. Press

ENTER

14.0

USE DNS Y/N

2-NO

Option 2

–

to allow the terminal to use Paymark IP address.

15.0

IP Primary

HOST IP ADDRESS
117.120.34.110

This parameter specifies the Primary Host IP Address. By default, it is set to

117.120.34.110

. Press

ENTER.

16.0

IP Secondary

HOST IP ADDRESS
117.120.32.110

This parameter specifies the Secondary Host IP Address. By default, it is set to

117.120.32.110

. Press

ENTER.

17.0

SAVE CONFIG Y/N

Terminal prompts to save configuration. Press

ENTER

to save configuration on the

terminal or

CLEAR

to exit and return to idle screen.

18.0

START TCP-IP Y/N

Terminal prompts to start TCP-IP link. Press

ENTER

to start the link or

CLEAR

exit without starting.

Содержание iCT2XX




















































































































































Результаты поиска

Содержание iCT2XX

Отзывы:

Похожие инструкции для iCT2XX

Бренды по названию

Популярные бренды

Ingenico iCT2XX, Руководство по эксплуатации

Результаты поиска

Содержание iCT2XX

Отзывы:

Похожие инструкции для iCT2XX

Бренды по названию

Популярные бренды