Ingenico iCT2XX Скачать руководство пользователя страница 123

Страница: 123 / 147

SKYZER TECHNOLOGIES

PAGE 123 OF 147

INGENICO ICT2XX PTS2018 PAYMARK OPERATING MANUAL

Version 1.00

6.0

PURCHASE AMOUNT?

$0.00

Key in the purchase amount and press

ENTER

7.0

PROCESSING NOW

PROCESSING NOW

will be displayed on the terminal and pinpad while

communicating with the host and the transaction is being processed.

8.0

ACCEPTED XXXXXX

PRESS ENTER

If the transaction is accepted then the terminal and pinpad will display

ACCEPTED

followed by the authorization ID number.

NOTE:

The terminal beeps and requires the merchant to press

ENTER

for the

completion of the transaction and returns to idle screen.

9.0

DECLINED XXXXXX

PRESS ENTER

If the transaction is declined then the terminal and pinpad will display

DECLINED

followed by the authorization ID number.

NOTE:

The terminal beeps and requires the merchant to press

ENTER

for the

completion of the transaction and returns to idle screen.

NOTE:

There is no receipt printed for this transaction since the only requirement

is for the merchant to obtain approval for the cheque. The response message
stays on the display until the merchant presses

ENTER

11.13 Merchant Administration Functions

The following standard merchant administration functions are available:

NOTE

: When set up as a multi-merchant device, the terminal will first prompt for

the selection of the particular merchant for each of the administration
functions above.

11.13.1

Terminal Totals

This function allows the merchant to determine the total count and amount of
all accepted transactions supported by the terminal since the totals where last
reset by the merchant.

Step

Terminal Display

Description

1.0

PAYMARK EFTPOS
1.EFTPOS MENU
2.TIPPING MENU
3.HOSPITALITY MENU
4.ADMIN MENU
5.SUPERVISOR MENU

Press

MENU

key and then scroll through using down arrow key until

ADMIN MENU

is shown on the display.

Press the corresponding number key or

ENTER

access ADMIN menu.

2.0

ADMIN MENU
1.TOTAL
2.INQUIRY
3.CUTOVER

Press the corresponding number key or down arrow key to select

TOTAL

to perform

a shift totals.

3.0

1 Merchant 1
2 Merchant 2
3 Merchant 3

Only applicable with Multi-Merchant setup.

Select the corresponding number on the terminal to select the Merchant followed by

ENTER

Содержание iCT2XX




















































































































































Результаты поиска

Содержание iCT2XX

Отзывы:

Похожие инструкции для iCT2XX

Бренды по названию

Популярные бренды

Ingenico iCT2XX, Руководство по эксплуатации

Результаты поиска

Содержание iCT2XX

Отзывы:

Похожие инструкции для iCT2XX

Бренды по названию

Популярные бренды