IMET GBS 218 Скачать руководство пользователя страница 9

TRADUCTION OF THE ORIGINAL INSTRUCTIONS FOR USE 

 GBS 218 / AutoCut ED.2010eng rev.00 

9/35 

 

 

7 - INSTALLATION 

The machine can work according to the parameters provided by the manufacturer if it is rightly installed and the minimum 
requirements are observed, as follows : 
- Machine mus

t be used indoor and with temperatures  from +5 to + 40 ° C. 

- The relative humidity of the environment must not  go over 95%. 
- The nominal value of the  voltage of electric energy must be b - 10 and the frequency of the nominal value 
must be b - 2%. 
The floor must have good characteristiques of capacity and level. 
Floor space, operator position and working area are indicated in the included drawing that concerns the machine only 
without fittings as optional. 
Work table must be leveled: by using the screws and nuts (not supplied) put in the little feet holes to fix the machine to the 
floor (it is especially necessary with connected accessories). 

The included electrical schemes reproduces the necessary details to arrange the connections, to be predisposed 
for 2KW power request. 
 

Earthing of all the electric parts with a dedicated GREEN/YELLOW wire, connected with a TN 
system  to  the  supply  cable.  A  supplementary  earthing  point 

–  indicated  with  PE  –  can  be 

located on the metallic structure of the machine.

 

At  the  origin  of  the  power  supply  cables  a  device  (such  as  fuses)  to  protect  against 
overloading has to be installed. On the models equipped with electronic variable-speed drive 
unit (ESC),  in order to connect the differential  protection on the  power supply line,  switches 
with a threshold of interference on the power dissipation of not less than 300 mA   (size 0.3 A 
or higher is recommended) have to be employed, having possibly time adjustment availability 
(0>1.5 sec).

 

 

E.M.C. - Electromagnetic noise

 

 

The user is responsible for installing and using this saw according to the manufacturer’s guidelines 
outlined in this manual. This equipment complies with the protection requirements established by the 
Directives  2006/42/CE,  2004/108/CE,  concerning  Electromagnetic  Compatibility  (EMC).  It  is  in 
compliance also with the technical guidelines of the Norms EN 55011, EN 50082-2 and it is intended 
for industrial and not for household use. 

 

 

Before installing the machine the user must take into account possible electromagnetic problems of 
the working area. In particular we suggest to install the equipment away from:

 

- signalling, control and telephone cables;

 

- radio-television transmitters and receivers;

 

 

The supply cable has to be as short as possible, with no twists. All doors, coverings and frame have 
to be closed when the saw is running. Do not make any modifications to the machine except for 
adjustments and replacements allowed/recommended by the manufacturer. Follow the maintenance 
schedule.

 

 

 

 

 

8 - MOVING AND TRANSIT

 

Содержание GBS 218




































Отзывы: