Illinois Tool Works IJ4000 Скачать руководство пользователя страница 64

Страница: 64 / 78

IJ4000 Impulse Jet

Appendix B: Theory of Operation

5765-018 Operations Manual Rev J

Page 64

MART

-IDS Ink and Vacuum Control PCB

LEDs:

LED1:

NOT DEFINED.

LED2:

Red; indicates a print head is signaling that the print

head reservoir is low and the ink out timer has expired.

LED3:

Green; indicates a print head is signaling for the vacuum

pump to turn on.

LED4:

Green; indicates a print head is signaling for the liquid

pump to turn on.

LED5:

Red; indicates that the waste bottle is full.

LED6:

Red; turns on, off, and flashes with the beacon. Off

indicates ink is OK, on indicates ink is low, slow flash

(1 Hz) indicates ink is out, and fast flash (6 Hz) indicates

that the waste bottle is full or the pump was turned on for

more than 10 seconds.

LED7:

Yellow; indicates ink is low in the S

MART

-IDS reservoir.

Connectors:

SW1:

NOT DEFINED.

P1:

MART

-IDS I/O connector.

J1:

Beacon.

J2:

External beacon.

J3:

Liquid pump.

J4:

Vacuum pump.

J5:

Power (12V).

J6:

Reservoir float switch.

J7:

Waste bottle float switch.

J8:

Programming port, for programming U1 via a PC.

J10:

Pressure sensor for flushing solvent

J11:

RFID communication

Содержание IJ4000















































































Результаты поиска

Содержание IJ4000

Отзывы:

Похожие инструкции для IJ4000

Бренды по названию

Популярные бренды

Illinois Tool Works IJ4000, Руководство по эксплуатации

Результаты поиска

Содержание IJ4000

Отзывы:

Похожие инструкции для IJ4000

Бренды по названию

Популярные бренды