Illinois Tool Works IJ4000 Скачать руководство пользователя страница 21

Страница: 21 / 78

IJ4000 Impulse Jet

Section 2: Quick Start

5765-018 Operations Manual Rev J

Page 21

Step 9: Priming the Print Head and Testing Print Quality

1. Ensure caps and plugs (vent, vacuum, and ink inlet) from the rear of the print head

have been removed and stored (see diagram).

2. Install the previously primed ink line and vacuum line into the rear of the print

head.

3. Ensure all print heads are at operating temperature.
4. Ensure that the shipping cap is installed for priming.

NOTE:

Print is disabled until the print head is fully heated. Wait until the "AT TEM-

PERATURE" LED is illuminated on the rear of the print head prior to any print sam-

pling.

5. Press and hold the Prime button on the rear of the print head until the S

MART

- IDS

Beacon flashes once. Repeat this step once more.

6. Remove the ship cap (see diagram) and store on the side of the 768E print head,

or on the top of the 384E print head.

NOTE:

Do not use lint-free wipes in the print channel; use foam swabs instead.

7. Use a foam swab to lightly wipe the orifice plate in a vertical

downward motion.

8. Prime the print head by pressing the button once, quickly

(ACS).

9. Print can be tested by slowly passing a sheet of paper in front

of the print head after pressing the All Channel Print button.
A solid image will print for approximately 3 seconds.

10. If the 384E sample is 50,8mm (2in) tall with no gaps, the print

head is ready.
If the 768E sample is 101,6mm (4in) tall with no gaps, the

print head is ready.

REMOVE AND

SAVE WHITE INK

INLET PLUG

LEAVE THE RED

VENT FILTER IN

PLACE

REMOVE

VENT CAP

REMOVE AND

SAVE PLUG

384E PRINT HEAD

(See next page for 768E Print Head)

AT TEMPERATURE LIGHT

IS ILLUMINATED

HEATER ON

ALL CHANNEL

PRINT
BUTTON

ACS / PRIME
BUTTON

Содержание IJ4000















































































Результаты поиска

Содержание IJ4000

Отзывы:

Похожие инструкции для IJ4000

Бренды по названию

Популярные бренды

Illinois Tool Works IJ4000, Руководство по эксплуатации

Результаты поиска

Содержание IJ4000

Отзывы:

Похожие инструкции для IJ4000

Бренды по названию

Популярные бренды