Illinois Tool Works IJ4000 Скачать руководство пользователя страница 40

Страница: 40 / 78

IJ4000 Impulse Jet

Section 4: Troubleshooting

5765-018 Operations Manual Rev J

Page 40

Impulse Jet Print Head:

System Symptom

Possible Cause

Operational Test Method

ACS Cycle will not operate

No S

MART

-IDS to Controller Cable

connection. No S

MART

-IDS power.

No Controller to Print Head connec-
tion.

Inspect S

MART

-IDS communication cable and ensure connection

to Interface Board. See “Step 6: Electrical Cable Connections” on
page 16.

Ink overfills and drips after ACS
Cycle

Vacuum Tubing & Connections

Confirm all tubing connections are tight between S

MART

-IDS and

every print head. Confirm that the waste bottle is tight and not

cross-threaded. Confirm that the in-line vacuum filter is tight. Do

not over-tighten.

Print Head will not heat, “At Tem-
perature” LED never turns on

Print Engine or PC Board

Return print head to manufacturer.

Missing print.

Air in Print Head

Air in the Print Head is the most likely cause of missing channels.
Refer to “Missing Print” on page 23 for bleeding procedures.

Ink Reservoir in Print Head does not
refill, or no ink pumps out during an
ACS or Prime Cycle. (384E)

Solenoids or PC Board

Return print head to manufacturer.

Print Head will not print. (384E)

PC Board

Return print head to manufacturer.

Ink Reservoir in Print Head does not
refill, or no ink pumps out during an
ACS or Prime cycle. (768E)

Solenoids

Remove power from the Print Head. Disconnect solenoid cable

harness. Purge, intake, and return solenoids are pinned on 1-2,

3-4, and 5-6, respectively. The Intake Valve controls ink into the

Reservoir, and the Purge Valve controls ACS and Prime. Check

the respective valve pins for resistance. An open coil should be

replaced.

Содержание IJ4000















































































Результаты поиска

Содержание IJ4000

Отзывы:

Похожие инструкции для IJ4000

Бренды по названию

Популярные бренды

Illinois Tool Works IJ4000, Руководство по эксплуатации

Результаты поиска

Содержание IJ4000

Отзывы:

Похожие инструкции для IJ4000

Бренды по названию

Популярные бренды