Illinois Tool Works IJ4000 Скачать руководство пользователя страница 34

Страница: 34 / 78

IJ4000 Impulse Jet

Section 3: Maintenance and Shutdowns

5765-018 Operations Manual Rev J

Page 34

Storage Life of a FACTORY SEALED Bottle of Ink

•

ScanTrue II: 12 months from date of manufacture.

•

ScanTrue II Plus: 18 months from date of manufacture.

•

Recommended storage temperature: 4° to 40°C (40° to 104°F).

•

Recommended storage relative humidity: 5 - 90% relative humidity with no condensation.

Temperatures above or below the recommended storage temperature for a period greater than one week will reduce the storage life of the ink.

NOTE:

Do not shake the bottle of ink before use. Agitating the ink may introduce air into the Print Head. If shaken, the bottle must sit for at least

two hours before use.

Use Life of an OPENED Bottle of Ink

•

ScanTrue II: 3 months from opening.

•

ScanTrue II Plus: 6 months from opening.

Exposure to air, temperature and relative humidity will affect the useful life of the ink.

Содержание IJ4000















































































Результаты поиска

Содержание IJ4000

Отзывы:

Похожие инструкции для IJ4000

Бренды по названию

Популярные бренды

Illinois Tool Works IJ4000, Руководство по эксплуатации

Результаты поиска

Содержание IJ4000

Отзывы:

Похожие инструкции для IJ4000

Бренды по названию

Популярные бренды