Illinois Tool Works IJ4000 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 78

background image

IJ4000 Impulse Jet

Section 4: Troubleshooting

5765-018 Operations Manual Rev J

Page 41

Impulse Jet Print Head (continued):

Photosensor Sensitivity Test

This test will determine if the photosensor sensitivity is adjusted correctly for the application.
1. Place object approximately 6,4mm (.25in) in front of photosensor; photosensor should sense object.
2. Place object near the center of the guide rails; photosensor should sense object.
3. Place object on far guide rail; photosensor should not sense object.
4. Check that objects on the far side of conveyor do not trip the photosensor.
5. Check that color differences in product do not cause multiple photosensor trips at the farthest sensing distance.

NOTE:

The test object should be a sample of the actual product. For photosensor sensitivity adjustment procedure, refer to the photosensor

manufacturer’s instructions.

NOTE:

If the red LED on the photosensor fails to illuminate when an object is placed in front of (but not touching) the photosensor, it indicates

that the photosensor is disconnected, or the power supply or photosensor has failed.

System Symptom

Possible Cause

Operational Test Method

Ink Reservoir in Print Head does not
refill, or no ink pumps out during an
ACS or Prime cycle. (768E)
(Continued.)

PC Board

Check the LED indicators on the board.
LED2: Green; indicates Print Head is requesting S

MART

-IDS to

turn Liquid Pump on.
LED9: Green; indicates Intake Solenoid Valve is open.
LED8: Green; indicates Print Head Reservoir is full.
LED3: Green; indicates Print Head Reservoir is low and Ink Out
Timer has expired.

Print Head will not print. (768E)

PC Board

Make sure all print head cables and the print engine cable are
seated at each end. Check the Test Points and LED indicators on
the board.
TP1: High voltage supply to driver IC (U9). The voltage level is
set via a sense resistor in the print engine (40-150 VDC).
LED6: Green; indicates high voltage is low.

«
...
39
40
41
42
43
...
»

Содержание IJ4000















































































Отзывы:

Нет отзывов

Похожие инструкции для IJ4000

Бренд: CAB Страницы: 263

Бренд: Canon Страницы: 300

Бренд: Canon Страницы: 288

Бренд: MAKER MADE Страницы: 21

Бренд: Canon Страницы: 58

Бренд: Canon Страницы: 30

PIXMA MX882 Series

Бренд: Canon Страницы: 34

Бренд: Canon Страницы: 4

Бренд: Canon Страницы: 913

Laser Class 700 Series

Бренд: Canon Страницы: 30

Laser Class 700 Series

Бренд: Canon Страницы: 6

Laser Class 700 Series

Бренд: Canon Страницы: 6

Laser Class 700 Series

Бренд: Canon Страницы: 108

PIXMA MX860 series

Бренд: Canon Страницы: 9

imagePROGRAF iPF9400

Бренд: Canon Страницы: 8

PIXMA MX860 series

Бренд: Canon Страницы: 93

Бренд: Canon Страницы: 20

Бренд: Canon Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды