Illinois Tool Works IJ4000 Скачать руководство пользователя страница 39

Страница: 39 / 78

IJ4000 Impulse Jet

Section 4: Troubleshooting

5765-018 Operations Manual Rev J

Page 39

MART

-IDS (continued)

System Symptom

Possible Cause

Operational Test Method

Liquid Pump and
Vacuum Pump do
not turn on, and light
is off on power
switch

Power Supply

Ensure S

MART

-IDS switch is turned on.

Check for power LED on Internal Power Supply Board. If LED is illuminated, check power supply

output on P2. It should be 12VDC.

Beacon light does
not illuminate at ink
out

Power Supply

Ensure S

MART

-IDS switch is turned on.

Check for power LED on Internal Power Supply Board. If LED is illuminated, check power supply

output on P2. It should be 12VDC.

PC Board

Check the LED indicators and connector voltages on the board.
LED5: Red; indicates the Waste Bottle is full.
LED6: Red; turns on, off, and flashes with the Beacon. Off indicates ink is OK, On indicates ink is

low, Slow Flash (1Hz) indicates ink is out, and Fast Flash (6Hz) indicates the Waste Bottle is full or

the pump was turned on for 10 seconds.
J5: Power connector; 12VDC when power is turned on.
J1: Beacon connector; 12VDC when Beacon is on.

12V Beacon Bulb

Unplug the Beacon from the board and check the resistance of the bulb. If the bulb is open,

replace it.

Содержание IJ4000















































































Результаты поиска

Содержание IJ4000

Отзывы:

Похожие инструкции для IJ4000

Бренды по названию

Популярные бренды

Illinois Tool Works IJ4000, Руководство по эксплуатации

Результаты поиска

Содержание IJ4000

Отзывы:

Похожие инструкции для IJ4000

Бренды по названию

Популярные бренды