background image

UK

IO-Link master

7

 

► Devices that are designed for mounting in housings or control cabinets must 

only be operated and controlled after they have been installed with the housing 

closed� Desktop or portable units must only be operated and controlled in 

enclosed housings�

 

► Measures should be taken to ensure the proper restart of programs interrupted 

after a voltage dip or failure� This should not cause dangerous operating states 

even for a short time� If necessary, an emergency stop must be carried out�

 

► Wherever faults in the automation system may cause personal injuries or 

damage to property, external measures must be implemented to ensure a safe 

operating state in the event of a fault or malfunction (e�g� by means of separate 

limit switches, mechanical interlocks etc�)

 

► The electrical installation must be carried out in accordance with the relevant 

regulations (e�g� with regard to cable cross-sections, fuses, PE)�

 

► All work relating to transport, installation, commissioning and maintenance 

must only be carried out by qualified personnel� (IEC 60 364 or HD 384 or 

DIN VDE 0100 and national work safety regulations have to be observed)�

 

► All shrouds and doors must be kept closed during operation�

3   Documentation

This documentation relates to the hardware and firmware status at the time of 

editing this manual� The features of the devices are continuously developed further 

and improved� 

4  Functions and features

The devices have been designed for use in applications described in this manual 

and the device-specific data sheets�
Adhere to the data indicated in the data sheets and in the manual� If the handling 

specifications and safety instructions for configuration, installation and operation 

indicated in the documentation are adhered to, the devices normally do not lead to 

a danger for persons and objects�

The input and output devices of the IO-Link master have been designed for 

automation tasks in harsh environmental conditions� The devices meet the 

requirements of IP65/67 protection rating� They enable direct connection of 

sensors and actuators in an environment close to the station�
The devices are available with M12 connection technology�
The devices cannot be extended and have a directly integrated fieldbus 

connection and I/O level� They are used for distribution in the field when only a few 

digital or analogue I/O points are required�

Содержание ECOMAT 300 AL1000






























































Отзывы: