IFM ECOMAT 300 AL1000 Скачать руководство пользователя страница 6

Страница: 6 / 61

IO-Link master

2 Safety instructions

These instructions contain texts and figures concerning the correct handling of the

device and must be read before installation or use�
Observe the operating instructions� Non-observance of the instructions, operation

which is not in accordance with use as prescribed below, wrong installation or

incorrect handling can seriously affect the safety of operators and machinery�

► Prepare installation

► Disconnect the power supply of the device�

► Ensure that devices cannot be accidentally restarted�

► Verify safe isolation from the supply�

► Earth and short circuit�

► Cover or enclose adjacent units that are live�

► Follow the specific mounting instructions of the device�

► Only suitably qualified personnel in accordance with EN 50 110-1/-2 (VDC 0105

part 100) is permitted to work on this device/system�

► Before installation and before touching the device ensure that you are free of

electrostatic charge�

► The functional earth (FE) must be connected to the protective earth (PE) or to

the potential equalisation� The system installer is responsible for implementing

this connection�

► Connection cables and signal lines must be installed in such a manner that

inductive and capacitive interference do not impair the automation functions�

► Install automation equipment and related operating elements in such a way that

they are protected against unintentional operation�

► Suitable safety hardware and software measures should be implemented for

the I/O interface so that a line or wire breakage on the signal side does not

result in undefined states in the automation device�

► Ensure a reliable electrical isolation of the low voltage for the 24 V supply�

Only use power supplies compliant with IEC 60 364-4-41 or HD 384�4�41 S2

(VDE 0100 part 410)�

► Fluctuations or deviations of the mains voltage from the rated value must not

exceed the tolerance limits specified in the technical data; otherwise this may

cause malfunction and dangerous operation�

► E-stop devices to IEC/EN 60 204-1 must be effective in all operating modes of

the automation device� Unlatching the e-stop devices must not cause restart�

Содержание ECOMAT 300 AL1000






























































Результаты поиска

Содержание ECOMAT 300 AL1000

Отзывы:

Похожие инструкции для ECOMAT 300 AL1000

Бренды по названию

Популярные бренды

IFM ECOMAT 300 AL1000, Руководство по эксплуатации устройства

Результаты поиска

Содержание ECOMAT 300 AL1000

Отзывы:

Похожие инструкции для ECOMAT 300 AL1000

Бренды по названию

Популярные бренды