IFM ECOMAT 300 AL1000 Скачать руководство пользователя страница 12

Страница: 12 / 61

IO-Link master

► Do not install network/bus cables together with or parallel to power supply

lines�

► Separate network/bus cables on cable bridges or in cable ducts from power

supply lines using isolating segments�

► Install network/bus cables as far away as possible from sources of interference,

such as motors and welding equipment�

► For long cable connections, install an additional equipotential bonding line

between the terminal points�

9.5 Cable routing outside buildings

► Install network/bus cables in metal pipes that are grounded on both sides or in

concrete cable ducts with continuous reinforcement�

► For long cable connections, install an additional equipotential bonding line

between the terminal points�

9.6 Installing network/bus cables between buildings
9.6.1 Causes of surge voltages

Surge voltages occur as a result of switching operations, electrostatic discharge,

and lightning discharge� Surge voltages can be inductively, capacitively or

galvanically coupled into electrical cables for mains supply, measured value

transmission, and data transmission� In this way, surge voltages reach the power

supply units and the interfaces of systems and devices�

9.6.2 Equipotential bonding line

Install an additional equipotential bonding line between the grounding points of

buildings, preferably in the form of

– a metal-reinforced concrete channel,

– an additional grounding cable or

– a metal pipe�

9.6.3 Surge protective devices

ifm recommends wiring all the wires of the cable to surge protective devices in order to protect the

devices against surge voltages�

Observe all national and international regulations when installing surge protective devices�

Содержание ECOMAT 300 AL1000






























































Результаты поиска

Содержание ECOMAT 300 AL1000

Отзывы:

Похожие инструкции для ECOMAT 300 AL1000

Бренды по названию

Популярные бренды

IFM ECOMAT 300 AL1000, Руководство по эксплуатации устройства

Результаты поиска

Содержание ECOMAT 300 AL1000

Отзывы:

Похожие инструкции для ECOMAT 300 AL1000

Бренды по названию

Популярные бренды