IFM ECOMAT 300 AL1000 Скачать руководство пользователя страница 10

Страница: 10 / 61

IO-Link master

8.1 Diagnostic and status indicators
8.1.1 Diagnostics

The diagnostic indicators (green/yellow/red) indicate whether an error is present

or not� In case of an error, they indicate the error type and location� The device is

operating correctly if all green indicators are on�

8.1.2 Status

The status indicators (yellow) indicate the signal state of the corresponding input/

output or of the IO-Link port� If the yellow status indicators are on, this indicates

signal state “1” of the input/output signal�
The devices have three main areas for diagnostics and status indicators�

● Indicators for the network/bus system (network/bus-specific) - Data

● Indicators for the power supplies - Power

● Indicators for the inputs and outputs and the IO-Link ports (device-specific) -

Signal

Data

Power

Signal

9 Installation

When preparing for cable installation, the local conditions and the corresponding

mounting regulations are very important� Cables can be installed, for example, in

cable ducts or on cable bridges�

Содержание ECOMAT 300 AL1000






























































Результаты поиска

Содержание ECOMAT 300 AL1000

Отзывы:

Похожие инструкции для ECOMAT 300 AL1000

Бренды по названию

Популярные бренды

IFM ECOMAT 300 AL1000, Руководство по эксплуатации устройства

Результаты поиска

Содержание ECOMAT 300 AL1000

Отзывы:

Похожие инструкции для ECOMAT 300 AL1000

Бренды по названию

Популярные бренды