manualshive.com logo in svg

IDT TSI384, Руководство пользователя

Пользовательский мануал для продукта IDT TSI384 доступен для загрузки бесплатно на manualshive.com. Руководство содержит информацию о настройке и использовании продукта. Скачайте мануал прямо сейчас, чтобы получить все необходимые инструкции по эксплуатации.

Поделиться
Скачать
background image

9. Error Handling

87

Tsi384 User Manual

May 5, 2014

Integrated Device Technology
www.idt.com

9.2.3

PCI/X Uncorrectable Data Errors

This section describes the bridge requirements for error handling when forwarding a downstream 
non-poisoned PCIe transaction to PCI/X and the bridge detects an uncorrectable data error. The error is 
detected on the PCI/X Interface. 

9.2.3.1

Immediate Reads and Split Responses

When the Tsi384 forwards a read request (I/O, Memory, or Configuration) downstream, it does the 
following when it detects an uncorrectable data error on the destination interface while receiving an 
immediate response or split response from the completer: 

1.

MDP_D bit is set in the 

“PCI Secondary Status and I/O Limit and Base Register”

 

if the S_PERESP 

bit is set in the 

“PCI Bridge Control and Interrupt Register”

2.

D_PE in the 

“PCI Control and Status Register”

 is set

3.

PCI_PERRn is asserted on the PCI/X Interface if the S_PERESP bit is set in the 

“PCI Bridge 

Control and Interrupt Register”

4.

UDERR bit is set in 

“PCIe Secondary Uncorrectable Error Status Register”

 

5.

Header is logged in the 

“PCIe Secondary Header Log 1 Register”

 and the SUFEP field is updated 

in the 

“PCIe Secondary Error Capabilities and Control Register”

 if UDERR Mask bit is clear in the 

“PCIe Secondary Uncorrectable Error Mask Register”

 and SUFEP is not valid

6.

Error Fatal or Non-Fatal message is generated on PCIe as per the severity level of UDERR bit in 

“PCIe Secondary Uncorrectable Error Severity Register”

 if the UDERR Mask bit is clear in 

“PCIe 

Secondary Uncorrectable Error Mask Register”

 and either SERR_EN bit is set in the 

“PCI Control 

and Status Register”

 or FTL_ERR_EN/NFTL_ERR_EN bit is set in the 

“PCIe Device Control and 

Status Register”

7.

S_SERR bit is set in the 

“PCI Control and Status Register”

 if an error message (Fatal/Non-Fatal) is 

generated and S_SERR bit is set in the 

“PCI Control and Status Register”

 

8.

FTL_ERR_DTD/NFTL_ERR_DTD bit is set in the 

“PCIe Device Control and Status Register”

For an immediate read transaction, if the Tsi384 detects an uncorrectable data error on the destination 
bus it continues to fetch data until the byte count is satisfied, or the target on the destination bus ends 
the transaction. When the bridge creates the PCIe completion, it forwards it with successful completion 
status and poisons the TLP. For PCI-X, an uncorrectable data error on a split response does not affect 
the handling of subsequent split completions. 

9.2.3.2

Non-Posted Writes

When the Tsi384 detects PCI_PERRn asserted on the PCI/X Interface while forwarding a 
non-poisoned non-posted write transaction from PCIe, it does the following:

1.

If the target completes the transaction immediately with a data transfer, the Tsi384 generates a 
PCIe completion with Unsupported Request status to report the error to the requester

2.

PERR_AD bit is set in the 

“PCIe Secondary Uncorrectable Error Status Register”

3.

MDP_D bit in the 

“PCI Secondary Status and I/O Limit and Base Register”

 is set if S_PERESP bit 

is set in the 

“PCI Bridge Control and Interrupt Register”

Содержание TSI384


























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TSI384

GE MDS SD Series Setup Manual preview
MDS SD Series
Бренд: GE Страницы: 4
Data Translation DT300 Series Getting Started Manual preview
DT300 Series
Бренд: Data Translation Страницы: 98
YASKAWA A1000 Series Installation Manual preview
A1000 Series
Бренд: YASKAWA Страницы: 34
Texas Instruments ThunderLAN TNETE100A Programmer'S Manual preview
ThunderLAN TNETE100A
Бренд: Texas Instruments Страницы: 179
Paradyne Comsphere 3510 User Manual preview
Comsphere 3510
Бренд: Paradyne Страницы: 85
Usr USR4504 Installation Manual preview
USR4504
Бренд: Usr Страницы: 2
National Instruments Fieldpoint cFP-RTD-124 Operating Instructions Manual preview
Fieldpoint cFP-RTD-124
Бренд: National Instruments Страницы: 15
IEI Technology PUZZLE-IN003B User Manual preview
PUZZLE-IN003B
Бренд: IEI Technology Страницы: 86
Dahua Technology Lite N42B1P Series Quick Start Manual preview
Lite N42B1P Series
Бренд: Dahua Technology Страницы: 14
TANDBERG D5018501 Hardware User Manual preview
D5018501
Бренд: TANDBERG Страницы: 3
Enterasys Enterasys Matrix 2G4082-25 Hardware Installation Manual preview
Enterasys Matrix 2G4082-25
Бренд: Enterasys Страницы: 58
BIIZZY zoomno MSC-5578 Setup Instructions preview
zoomno MSC-5578
Бренд: BIIZZY Страницы: 2
ebm-papst R3G560-AH02-03 Operating Instructions Manual preview
R3G560-AH02-03
Бренд: ebm-papst Страницы: 13
IEI Technology PulM-1G4T-I211 Quick Installation Manual preview
PulM-1G4T-I211
Бренд: IEI Technology Страницы: 2
Xantech CC62 Installation Instructions preview
CC62
Бренд: Xantech Страницы: 5
audemat DIGIPLEXER 246 User Manual preview
DIGIPLEXER 246
Бренд: audemat Страницы: 93
Gigamon GigaVUE H TA100-CXP Hardware Installation Manual preview
GigaVUE H TA100-CXP
Бренд: Gigamon Страницы: 115
Multitech MultiModem ISIHP-2S User Manual preview
MultiModem ISIHP-2S
Бренд: Multitech Страницы: 155

Бренды по названию

Популярные бренды

Загрузить еще бренды