IDT TSI384 Скачать руководство пользователя страница 88 | Manualshive

Страница: 88 / 281

background image

9. Error Handling

88

Tsi384 User Manual
May 5, 2014

Integrated Device Technology

www.idt.com

4.

Header is logged in the

“PCIe Secondary Header Log 1 Register”

and the SUFEP field is updated

in the

“PCIe Secondary Error Capabilities and Control Register”

if PERR_AD Mask bit is clear in

the

“PCIe Secondary Uncorrectable Error Mask Register”

and SUFEP is not valid

5.

Error Fatal or Non-Fatal message is generated on PCIe as per the severity level of PERR_AD bit in

“PCIe Secondary Uncorrectable Error Severity Register”

if the PERR_AD Mask bit is clear in

“PCIe Secondary Uncorrectable Error Mask Register”

and either SERR_EN bit is set in the

Control and Status Register”

or FTL_ERR_DTD/NFTL_ERR_DTD bit is set in the

Control and Status Register”

6.

S_SERR bit is set in the

“PCI Control and Status Register”

if an error message (Fatal/Non-Fatal) is

generated and SERR_EN bit is set in the

“PCI Control and Status Register”

7.

FTL_ERR_DTD/NFTL_ERR_DTD bit is set in the

“PCIe Device Control and Status Register”

If the target signals split response, the Tsi384 terminates the transaction as it would for a split request
that did not have an error and takes no further action. If the returned split completion is a split
completion error message, the bridge returns a PCIe Completion with Unsupported Request status to
the requester.

9.2.3.3

Posted Writes

When the Tsi384 detects PCI_PERRn asserted on the PCI/X Interface while forwarding a
non-poisoned posted write transaction from PCIe, it does the following:

1.

Continues to forward the remainder of the transaction

2.

MDP_D bit in the

“PCI Secondary Status and I/O Limit and Base Register”

is set if S_PERESP bit

is set in the

“PCI Bridge Control and Interrupt Register”

3.

PERRn Assertion Detected Status bit is set in the

“PCIe Secondary Uncorrectable Error Status

4.

Header is logged in the

“PCIe Secondary Header Log 1 Register”

and the SUFEP field is updated

in the

“PCIe Secondary Error Capabilities and Control Register”

if PERR_AD Mask bit is clear in

the

“PCIe Secondary Uncorrectable Error Mask Register”

and SUFEP is not valid

5.

Error Fatal or Non-Fatal message is generated on PCIe as per the severity level of PERR_AD bit in

“PCIe Secondary Uncorrectable Error Severity Register”

if the PERR_AD Mask bit is clear in

“PCIe Secondary Uncorrectable Error Mask Register”

, and either SERR_EN bit is set in the

Control and Status Register”

or FTL_ERR_DTD/NFTL_ERR_DTD bit is set in the

Control and Status Register”

6.

S_SERR bit is set in the

“PCI Control and Status Register”

if an error message (Fatal/Non-Fatal) is

generated and SERR_EN bit is set in the

“PCI Control and Status Register”

7.

FTL_ERR_DTD/NFTL_ERR_DTD bit is set in the

“PCIe Device Control and Status Register”

9.2.3.4

PCI-X Split Read Completions

While forwarding a non-poisoned read completion from PCIe to PCI-X, if the Tsi384 detects
PCI_PERRn asserted by the PCI-X target, it does the following:

1.

Continues to forward the remainder of the split completion

2.

PERR_AD bit is set in the

“PCIe Secondary Uncorrectable Error Status Register”

«
...
86
87
88
89
90
...
»

Содержание TSI384


























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TSI384

Wisenet PRN-6400B4

Бренд: Hanwha Techwin Страницы: 14

Бренд: ZALMAN Страницы: 9

Бренд: Juniper Страницы: 7

Бренд: ZKTeco Страницы: 68

Бренд: Stepper Motor Canada Страницы: 5

Бренд: Rajant Страницы: 93

Бренд: TECO Страницы: 24

Бренд: netsys Страницы: 38

cPCI-3520 Series

Бренд: ADLINK Technology Страницы: 81

Бренд: iTON Страницы: 12

Бренд: Hakki Pilke Страницы: 48

CORIOview MWP Series

Бренд: Tvone Страницы: 24

ControlWave Remote Ethernet I/O

Бренд: Emerson Страницы: 3

Бренд: Emerson Страницы: 6

Bristol Helicoid Gauges

Бренд: Emerson Страницы: 1

ACC/ARTM-7221/SCSI

Бренд: Emerson Страницы: 62

Бренд: Emerson Страницы: 106

Бренд: Emerson Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды