IDT TSI384 Скачать руководство пользователя страница 103 | Manualshive

Страница: 103 / 281

background image

9. Error Handling

103

Tsi384 User Manual

May 5, 2014

Integrated Device Technology
www.idt.com

4.

S_SERR bit is set in

“PCI Control and Status Register”

if an error message (Fatal/Non-Fatal) is

generated and the SERR_EN bit is set in

“PCI Control and Status Register”

5.

FTL_ERR_DTD/NFTL_ERR_DTD bit is set in

“PCIe Device Control and Status Register”

9.4

Timeout Errors

This section discusses how the Tsi384 handles PCIe and PCI/X timeout errors.

9.4.1

PCIe Completion Timeout Errors

The PCIe Completion Timeout function allows requestors to abort a non-posted request if the
completion does not arrive within a reasonable period of time. When bridges act as initiators on PCIe
on behalf of internally generated requests, and requests forwarded from a secondary interface in PCI
mode, they act as endpoints for requests that they take ownership. When the Tsi384 detects a
completion timeout it responds as if a completion with Unsupported Request status has been received
and follows the rules for handling Unsupported Request Completions as described in

Request Completion Status”

. In addition, the bridge takes the following actions:

1.

CTO bit is set in

“PCIe Uncorrectable Error Status Register”

2.

Error Fatal or Non-Fatal message is generated on PCIe as per the severity level of the CTO bit in

“PCIe Uncorrectable Error Severity Register”

if CTO Mask bit is clear in

“PCIe Correctable Error

Mask Register”

and either SERR_EN bit is set in

“PCI Control and Status Register”

or

FTL_ERR_EN/NFTL_ERR_EN bit is set in

“PCIe Device Control and Status Register”

3.

S_SERR bit is set in

“PCI Control and Status Register”

if an error message (Fatal/Non-Fatal) is

generated and the SERR_EN bit is set in

“PCI Control and Status Register”

9.4.2

PCI Delayed Transaction Timeout Errors

If a delayed transaction timeout is detected the Tsi384 does the following:

1.

Error Fatal or Non-Fatal message is generated on PCIe as per the severity level of DTDTE bit in

“PCIe Secondary Uncorrectable Error Severity Register”

, if DTDTE Mask bit is clear in

Secondary Uncorrectable Error Mask Register”

or DISCARD_SERR bit is set

Control and Interrupt Register”

and either SERR_EN bit is set in

“PCI Control and Status

or FTL_ERR_EN/NFTL_ERR_EN bit is set in

“PCIe Device Control and Status

2.

No Header is logged

3.

S_SERR bit is set in

“PCI Control and Status Register”

if an error message (Fatal/Non-Fatal) is

generated and SERR_EN bit is set in

“PCI Control and Status Register”

«
...
101
102
103
104
105
...
»

Содержание TSI384


























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TSI384

Бренд: IBM Страницы: 86

Бренд: Garland Страницы: 4

Бренд: Maxim Страницы: 26

PARTNER Voice Messaging PC Card Release 2

Бренд: Lucent Technologies Страницы: 67

Fieldpoint cFP-RTD-124

Бренд: National Instruments Страницы: 15

HHM Series HHM2411

Бренд: TDK Страницы: 2

Бренд: East Coast Datacom Страницы: 19

Бренд: Active Communications Страницы: 10

Бренд: Gearlinx Страницы: 23

Бренд: Alcatel-Lucent Страницы: 12

Бренд: UMAX Technologies Страницы: 27

Бренд: Uctronics Страницы: 12

Бренд: Lanner Страницы: 99

Бренд: Dinstar Страницы: 103

Бренд: NetApp Страницы: 28

Бренд: abaco systems Страницы: 28

Бренд: Crestron Страницы: 16

Бренд: Lenovo Страницы: 152

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды