IDT TSI384 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 281

background image

2. Signal Descriptions

31

Tsi384 User Manual

May 5, 2014

Integrated Device Technology
www.idt.com

PCI_PAR64

PCI/X Bidir

Parity for 64-bit Transaction. This signal
serves the same purpose as PCI_PAR,
but is associated with PCI_AD[63:32]
and PCI_CBEn[7:4].

Pull-up (8.2K) to 3.3V.

PCI_PCIXCAP

PCI/X In

PCI-X capability. This signal determines
the PCI-X operating frequency (see

“PCI/X Clocking”

Embedded designs
For PCI mode, connect to ground.
For PCI-X mode at 66 MHz, pull down
with a 10K resistor and pull up with 56K
resistor.
For PCI-X mode at 133 MHz, pull up
with 56K.
Bused designs using PCI-X slots for
add- in cards
Pull up to 3.3V with a 56K resistor and
route the signal from slot to slot.

PCI_PCIXCAP_PU

PCI/X Bidir

PCI-X capability pull-up (see

Couple resistively to PCI_PCIXCAP
using a 1K resistor.

PCI_PERRn

PCI/X Bidir

Parity Error. This signal indicates a
parity error occurred during the current
data phase. The bus target that
receives the data asserts this signal.

Pull up (8.2K) to 3.3V.

PCI_PMEn

PCI/X In

Power Management Event. This signal
indicates a power management event
occurred (see

“Power Management”

Pull up (8.2K) to 3.3V.

PCI_REQn[3:0]

PCI/X In

PCI/X Bidir

Bus Request. These signals are used to
request access to the PCI/X bus. They
are used differently, however,
depending on whether or not the Tsi384
PCI/X arbiter is used. If the PCI/X
arbiter is used, then PCI_REQn[3:0] are
inputs used by external masters to
request access to the bus.
If an external arbiter is used,
PCI_REQn[0] is an output used by the
Tsi384 to request access to the bus,
while PCI_REQn[3:1] should be pulled
high, as they are still inputs.
The input/output mode is controlled by
the PWRUP_EN_ARB pin (see

“Power-up Signals”

Pull up (8.2K) to 3.3V.

PCI_REQ64n

PCI/X Bidir

Request 64-bit Transfer. The bus
master asserts this signal to indicate it
wants to perform a 64-bit transaction.
The bus master rescinds this signal at
the end of the transaction.

Pull up (8.2K) to 3.3V.

Table 3: PCI/X Interface Signals

(Continued)

Name

Pin Type

Description

Design Recommendation

«
...
29
30
31
32
33
...
»

Содержание TSI384


























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TSI384

All in One Printer

Бренд: Baracoda Страницы: 42

Бренд: CAME Страницы: 4

System x3630 M4

Бренд: IBM Страницы: 7

BIC 1I12-P2A25-M30MI1-BPX05-110

Бренд: Balluff Страницы: 12

Бренд: IEI Technology Страницы: 3

Бренд: Eneo Страницы: 68

Бренд: ACTi Страницы: 14

DAS-1800HR Series

Бренд: Keithley Страницы: 139

Бренд: Rockwell Automation Страницы: 21

Бренд: Crown Страницы: 7

Бренд: EVGA Страницы: 3

SmartRack SR42UBEXPKD

Бренд: Tripp Lite Страницы: 8

Бренд: Abus Страницы: 98

Бренд: Behringer Страницы: 15

11th Gen Intel Core U-Series

Бренд: IBASE Technology Страницы: 70

Бренд: Promax Страницы: 32

Бренд: Reach Страницы: 21

Бренд: NovaStar Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды