45
1. Press the MENU key to access the Calibration Menu.
- M E N U -
C A L I B R A T I O N
2. Press the ENTER key to access Pump Flow Calibration screen.
C A L I B R A T I O N
P U M P F L O W
3. Press the ENTER key to access Wet Pump Flow Calibration screen.
P U M P F L O W
W E T C A L
4.
Press the ENTER key to begin Flow Calibration
S E T M O T O R S P E E D
H I G H : 1 8 0 0 R P M
5.
Using the UP and/or DOWN arrow keys adjust the motor speed to an approximate high speed setpoint. This
speed is the high speed calibration point for the MPC MPC VECTOR that you will measure flow at.
6.
Press the ENTER key to accept the calibration speed.
P R E S S E N T E R T O
S T A R T M O T O R
T
HE MOTOR WILL START WHEN THE ENTER KEY IS PRESSED
.
MAKE SURE THAT YOUR SYSTEM IS
PREPARED FOR OPERATIONS BEFORE STARTING THE MOTOR
.
7.
Press the ENTER key to start the motor and advance to the calibration interval count down screen. The default
interval will be 60 seconds. Pressing the ENTER key will take the user immediately to the next screen. Shorter
drawdowns are available by using the ENTER key to terminate at the desired interval. All other keys abort the
calibration. Observe the final flow rate on your flow meter at the end of the interval as it must be entered in the
next step.
R U N N I N G 6 0 S E C S * *
M E T E R : 1 8 . 5 M A
* * 6 0 S E C O N D S W I L L E L A P S E B Y D E F A U L T
8.
Using the UP and/or DOWN arrow keys adjust the flow to your flow meter’s displayed flow rate value at the end
of the calibration interval.
F L O W A T 1 8 . 5 M A
F L O W : 2 5 . 2 G P H
9.
Press the ENTER key to accept the calibration flow rate and proceed to the low flow calibration point.
10.
Using the UP and/or DOWN arrow keys adjust the motor speed to an approximate low speed setpoint. This speed
is the low speed calibration point for the MPC VECTOR. This speed will produce a low flow and provide a flow
feedback signal to the controller. At this speed you will monitor flow rate from the flow meter and enter it via the
handheld unit.
Содержание Pulsafeeder MPC Vector
