manualshive.com logo in svg

ICS ICS-130, Руководство по эксплуатации

Поделиться
Скачать
ICS ICS-130 Скачать руководство пользователя страница 55

DOC E10523 Rev.D

 

 Interactive Circuits And Systems Ltd. 2000

 

51

 

6.5 P4 Local Bus Connector Details 
 
Suitable mating connectors are available from a number of manufacturers. The one listed is 
an example only. 
 
Connector on board:  8831E-026-170L (KEL Corporation) 
    P50E-026P1-RR1-TG (Robinson-Nugent) 
Mating connector:  8825E-026-175 KEL (with strain relief) 
    8825R-026-175 KEL (without strain relief) 
    P25E-026S-TG Robinson-Nugent 
Manufacturers:  KEL Corporation, (408)720-9044 
    Robinson-Nugent, (812)945-0211 
 
 

Pin 
No. 

Signal 
Name 

Description 

1 

ADC_CLK 

Distribution ADC Clock +ve. This PECL signal is used by sampling master to 
ensure all slaves sample at the same time. This signal is bussed from the sampling 
master to all slaves, and is driven by the master only. 

2 

/ADC_CLK 

Distribution ADC Clock -ve. This PECL signal is used by sampling master to ensure 
all slaves sample at the same time. This signal is bussed from the sampling master 
to all slaves, and is driven by the master only. 

3 

GND 

Digital Ground 

4 

SYNC 

ADC Frame Sync.  In multiple board systems, this signal is used by the sampling 
master to ensure the ADC’s output syncronisation on all boards. This signal is 
bussed from the sampling master to all slaves, and is driven by the master only. 

5 

GND 

Digital Ground 

6 

  - 

Not Used 

7 

GND 

Digital Ground 

8 

FSYNC 

Decimation Sync.  In multiple board systems, this signal is used by the samling 
master to ensure all boards decimate on the same sample. This signal is bussed 
from the sampling master to all slaves, and is driven by the master only. 

9 

GND 

Digital Ground 

10 

TRIG 

Distribution Trigger. This signal is used by the sampling master to ensule all boards 
trigger at the same time. This signal is bussed from the sampling master to all 
slaves, and is driven by the master only. 

11 

GND 

Digital Ground 

12 

FP_CLK 

Distribution FPDP Clock +ve. This PECL signal is used by FPDP master to ensure 
FPDP data transfers. This signal is bussed from the FPDF master to all slaves, and 
is driven by the master only. 

13 

PECL /FP_CLK 

Distribution FPDP Clock -ve. This PECL signal is used by FPDP master to ensure 
FPDP data transfers. This signal is bussed from the FPDF master to all slaves, and 

Содержание ICS-130






























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды