Icom IC-7200 Скачать руководство пользователя страница 76

Страница: 76 / 104

■

Quick set mode

Mode

Set mode item

Default setting

SSB

RF POWER

100%

MIC GAIN

50%

DATA MODE

OFF

RF POWER

100%

KEY SPEED

20WPM

CW PITCH

600Hz

SIDE TONE LEVEL

30%

SIDE TONE LIMIT

RTTY

RF POWER

100%

TWIN PEAK FILTER

OFF

RTTY MARK TONE

2125Hz

RTTY SHIFT

170Hz

RTTY KEY POLARITY

NORMAL

RF POWER

100%

MIC GAIN

50%

DATA MODE

OFF

RF power

(all modes)

This item adjusts the RF output power. The RF output
power can be adjusted from L (Low), 1% to 100% in 1%
steps.

100% (default)

Mic gain

(SSB/AM modes)

This item adjusts microphone gain from 0% to 100% in
1% steps.

50% (default)

Data mode

(SSB/AM modes)

This item turns the data mode ON or OFF.
When the data mode is turned ON, the audio input from
the [ACC] connector* is used for transmission instead of
[MIC] connector and the speech compressor function is
turned OFF.

* The desired connector can be selected. (p. 77)

on : Data mode operation is enabled.

(“ ” appears.)

oF : Data mode operation is disabled.

(“ ” disappears.)

OFF (default)

SET MODE

Содержание IC-7200









































































































Результаты поиска

Содержание IC-7200

Отзывы:

Похожие инструкции для IC-7200

Бренды по названию

Популярные бренды

Icom IC-7200, Инструкция по эксплуатации

Результаты поиска

Содержание IC-7200

Отзывы:

Похожие инструкции для IC-7200

Бренды по названию

Популярные бренды