Icom IC-7200 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 104

background image

34

4

RECEIVE AND TRANSMIT

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21

D

Convenient functions for transmit

• VOX (voice operated transmit)

(p. 53)

➥

Push

VOX

to turn the VOX function ON or OFF.

• “

” appears when the VOX function is ON.

➥

Push and hold

VOX

for 1 sec. to enter the VOX

set mode, then rotate

[DIAL]

to adjust the VOX

gain, anti VOX gain or VOX delay.

• Rotate

[M-CH]

to select an item.

• Speech compressor

(p. 57)

➥

Push

COMP

to turn the speech compressor ON

or OFF.

• “

” appears when the speech compressor is ON.

➥

Push and hold

COMP

for 1 sec. to enter the com-

pression level set mode, then rotate

[DIAL]

to ad-

just the compression level.

D

About 5 MHz band operation (USA version only)

Operation on the 5 MHz band is allowed on 5 dis-
crete frequencies and must adhere to the following:
• USB mode
• Maximum of 50 watts ERP

(Effective Radiated Power)

• 2.8 kHz bandwidth

It is the operator’s responsibility to set all controls so
that the transmission in this band meets the stringent
conditions under which we may use these frequen-
cies.

NOTE:

We recommend that you store these fre-

quencies, mode and filter settings into the mem-
ory channel for easy recall.

IC-7200

Display Frequency*

FCC Channel

Center Frequency*

5.33050 MHz

5.33200 MHz

5.34650 MHz

5.34800 MHz

5.36650 MHz

5.36800 MHz

5.37150 MHz

5.37300 MHz

5.40350 MHz

5.40500 MHz

* The channel center frequencies that are specified

by the FCC, show the center frequency of their
passband. However, the IC-7200 displays carrier
point frequency, so set 1.5 kHz below from FCC
channel center frequency.

To assist you in operating the 5 MHz band cor-
rectly within the rules specified by the FCC,
transmission is impossible on any 5 MHz band
frequency other than the 5 frequencies indicated in
the table above.

«
...
37
38
39
40
41
...
»

Содержание IC-7200









































































































Отзывы:

Нет отзывов

Похожие инструкции для IC-7200

Бренд: Harris Страницы: 162

Бренд: Icom Страницы: 48

Бренд: Icom Страницы: 392

Бренд: Icom Страницы: 24

Бренд: Icom Страницы: 286

Бренд: Nautel Страницы: 62

Бренд: Nautel Страницы: 56

Бренд: Nautel Страницы: 48

Бренд: Nauticam Страницы: 6

Бренд: MuxLab Страницы: 2

Бренд: Blaupunkt Страницы: 17

Бренд: Stabila Страницы: 10

Бренд: GBD Страницы: 4

HUMICAP HMW90 SERIES

Бренд: Vaisala Страницы: 118

King-Gage 5800 Series

Бренд: NOSHOK Страницы: 12

Бренд: sunair Страницы: 188

Бренд: Yanglousi Technology Страницы: 3

Бренд: TV Star Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды