Icom IC-7200 Скачать руководство пользователя страница 91

Страница: 91 / 104

PROBLEM

POSSIBLE CASE

SOLUTION

REF.

TRANSMIT

Transmitting is impos-
sible.

• The operating frequency is not set in a

ham band.

• Set the frequency in a ham band.

p. 25

Output power is too
low.

• Power is set to a lower power than max-

imum.

• Set the output power in quick set mode. p. 71

• Microphone gain is set too low.

• Set microphone gain to a suitable level

in quick set mode.

p. 71

• The antenna is not connected properly. • Reconnect the antenna connector.

—

• The antenna feed line is cut or shorted. • Check the feed line and correct any im-

proper conditions.

—

• The antenna is not properly tuned.

• Push

TUNER

to manually tune the an-

tenna or test with dummy load.

p. 67

• The antenna for another band is se-

lected.

• Select an antenna suitable for the oper-

ating frequency.

p. 67

No contact possible
with other stations.

• RIT function is activated.

• Push

RIT

to turn the function OFF.

p. 44

• Split function is activated.

• Push

SPLIT

to turn the function OFF.

p. 58

Transmitted signals are
distorted.

• Microphone gain is set too high.

• Set microphone gain to a suitable level

in quick set mode.

p. 71

• The compression level is set too high

with the speech compressor ON.

• Set compression level to a suitable po-

sition.

p. 57

DISPLA

Displayed frequency
does not change prop-
erly.

• The dial lock function is activated.

• Push

SPCH

to deactivate the function.

p. 29

• The internal CPU has malfunctioned.

• Reset the CPU.

pgs. 21,
84

SCAN

P r o g r a m m e d s c a n
does not stop.

• [RF/SQL] is assigned to RF gain control

and squelch is open.

• Reset [RF/SQL] control assignment and

set it to the threshold point.

p. 30

P r o g r a m m e d s c a n
does not start.

• The same frequencies have been pro-

grammed in scan edge memory chan-
nels.

• Program different frequencies into scan

edge memory channels.

p. 62

Memory scan does not
start.

• 2 or more memory channels have not

been programmed.

• Program 2 or more memory channels.

p. 62

MEMOR

The memory channels
cannot be selected
with rotating the [M-CH]
control.

• The [M-CH] control acts as the RIT con-

trol mode.

• Push

M-CH/RIT

SET

to set the

[M-CH]

con-

trol to memory channel control. (RIT
control indicator goes out).

p. 61

TROUBLESHOOTING

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21

Содержание IC-7200









































































































Результаты поиска

Содержание IC-7200

Отзывы:

Похожие инструкции для IC-7200

Бренды по названию

Популярные бренды

Icom IC-7200, Инструкция по эксплуатации

Результаты поиска

Содержание IC-7200

Отзывы:

Похожие инструкции для IC-7200

Бренды по названию

Популярные бренды