Icom IC-7200 Скачать руководство пользователя страница 90

Страница: 90 / 104

TROUBLESHOOTING

The following chart is designed to help you correct
problems which are not equipment malfunctions.

If you are unable to locate the cause of a problem
or solve it through the use of this chart, contact your
nearest Icom Dealer or Service Center.

PROBLEM

POSSIBLE CAUSE

SOLUTION

REF.

WER SUPPL

Power does not come
o n w h e n [ P W R ] i s
pushed.

• DC power cable is improperly connected. • Reconnect the power cable correctly.

p. 15

• Fuse is blown.

• Check for the cause, then replace the

fuse with a spare one.

(Fuse is installed in the DC power cable)

p. 83

• Battery is exhausted if you are using a

12 V battery as the power source.

• Check the battery voltage.

—

RECEIVE

No sound comes from
the speaker.

• Volume level is set too low.

• Rotate

[AF]

clockwise to obtain a suit-

able listening level.

p. 29

• The squelch level is closed.

• Rotate

[RF/SQL]

to 12 o’clock position

to open the squelch.

p. 30

• The transceiver is in the transmit mode. • Release

[PTT]

on the microphone or

check the SEND line of an external unit,
if connected.

—

• An external speaker or headphones are

connected.

• Check the external speaker or head-

phone plug connection.

p. 14

Sensitivity is too low,
and only strong signals
are audible.

• The antenna is not connected properly. • Reconnect to the antenna connector.

—

• The antenna feed line is cut or shorted. • Check the feed line and correct any im-

proper conditions.

—

• The antenna is not properly tuned.

• Push

TUNER

to manually tune the an-

tenna.

p. 67

• The attenuator function is activated.

• Push

P.AMP

ATT

to turn the function OFF.

p. 45

• The antenna for another band is se-

lected.

• Select an antenna suitable for the oper-

ating frequency.

p. 67

Receive audio is dis-
torted.

• The operating mode is not selected cor-

rectly.

• Select a suitable operating mode.

p. 29

Receive signal is dis-
torted by strong sig-
nals.

• The noise reduction is activated and the

noise reduction level is too high.

• Set the noise reduction level for maxi-

mum readability.

p. 50

• Noise blanker function is activated.

• Push

to turn the function OFF.

p. 49

• Preamp is activated.

• Push

P.AMP

ATT

to turn the function OFF.

p. 45

The shift frequency of
the RIT function cannot
be added/subtracted.

• The XFC (transmit frequency check

function) is turned ON.

• Turn the XFC (transmit frequency check

function) OFF in set mode.

p. 76

Содержание IC-7200









































































































Результаты поиска

Содержание IC-7200

Отзывы:

Похожие инструкции для IC-7200

Бренды по названию

Популярные бренды

Icom IC-7200, Инструкция по эксплуатации

Результаты поиска

Содержание IC-7200

Отзывы:

Похожие инструкции для IC-7200

Бренды по названию

Популярные бренды