Icom IC-7200 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 104

background image

q

PASSBAND TUNING CONTROLS [TWIN PBT]

Adjust the receiver’s DSP filter passband width.

(p. 46)

• The limit of the variable range depends on the pass-

band width and mode. The limit of the variable range
is half of the passband width, and PBT is adjustable in
200 Hz (AM) or 50 Hz (other models) steps.

• Rotate both [TWIN PBT] controls (PBT1 and PBT2) to

the same position shifts the IF.

4

What is the PBT control?

Generally, the PBT electronically narrows the IF
passband width to reject interference. This trans-
ceiver uses the DSP circuit for the PBT function.

PBT2

PBT1

Low cut

High cut

Center

TWIN PBT

TWIN PBT

TWIN PBT

–

+

w

NOISE BLANKER KEY

NB

(p. 49)

➥

Push to turn the noise blanker function ON or

OFF.

• “

” appears on the display.

➥

Push and hold for 1 sec to enter the noise

blanker set mode for setting the noise blanker
level and blank time; push again to return to nor-
mal operation.

• When entering the noise blanker set mode, the noise

blanker function is automatically turned ON.

4

What is the noise blanker?

The noise blanker reduces pulse-type noise such
as that generated by automobile ignition systems.
This function is not effective against non pulse-type
noise.

e

NR KEY

NR

(p. 50)

➥

Push to turn the noise reduction function ON or

OFF.

• “

” appears on the display.

➥

Push and hold for 1 sec. to enter the noise re-

duction level set mode; push again to return to
normal operation.

• When entering the noise reduction set mode, the

noise reduction function is automatically turned ON.

4

What is the Noise Reduction function?

The Noise Reduction (NR) function removes ran-
dom noise from the receiver passband. The level is
adjustable to allow maximum clarity without harm-
ing the intelligibility of the desired signal. Noise Re-
duction should generally not be used with digital
modes.

1

1

PANEL DESCRIPTION

i7200

MODE

TUNER

TS

FILTER

SPCH

V/M

A/B

SPLIT

M-CL

SCAN

SET

ATT

P.AMP

COMP

VOX

MNF

RIT

1

2

3

4

5

6

7

8

0

50

28

18

14

10

21

24

=

7

3.5

1.8

F-INP

M-CH/RIT

ENT

BAND

GENE

9

.

AGC

MW

ANF

METER

NR

NB

Speaker

t

r

e

w

Function
Display (p. 7)

u

i

y

q

o

■

Front panel

«
...
4
5
6
7
8
...
»

Содержание IC-7200









































































































Отзывы:

Нет отзывов

Похожие инструкции для IC-7200

Бренд: Harman Kardon Страницы: 2

Бренд: Harman Kardon Страницы: 44

Бренд: Harman Kardon Страницы: 176

Бренд: Harman Kardon Страницы: 3

Бренд: Icom Страницы: 2

Бренд: Icom Страницы: 39

Бренд: Icom Страницы: 32

IC-F5020 Series

Бренд: Icom Страницы: 24

Бренд: Icom Страницы: 48

Бренд: Icom Страницы: 4

Бренд: Icom Страницы: 39

IC-F1000 series

Бренд: Icom Страницы: 38

IC-F1000 series

Бренд: Icom Страницы: 26

Бренд: Icom Страницы: 8

Бренд: Icom Страницы: 52

Бренд: Icom Страницы: 8

Бренд: Icom Страницы: 179

Бренд: Icom Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды