Icom IC-7200 Скачать руководство пользователя страница 94

Страница: 94 / 104

Command table

Command Sub command

Description

—

Send frequency data.
(for transceive operation)

Select LSB mode
(for transceive operation)

Select USB mode
(for transceive operation)

Select AM mode
(for transceive operation)

Select CW mode
(for transceive operation)

Select RTTY mode
(for transceive operation)

Select CW-R mode
(for transceive operation)

Select RTTY-R mode
(for transceive operation)

—

Read band edge frequencies

—

Read operating frequency

—

Read operating mode

—

Set operating frequency

Select LSB mode

Select USB mode

Select AM mode

Select CW mode

Select RTTY mode

Select CW-R mode

Select RTTY-R mode

—

Select VFO mode

Select VFO A

Select VFO B

Equalize VFO A and VFO B

Exchange VFO A and VFO B

—

Select memory mode

0001−0201*

Select memory channel
*P1=0200, P2=0201

—

Memory write

—

Memory to VFO

—

Memory clear

Scan stop

Programmed/memory scan start

Programmed scan start

Memory scan start

Set scan resume OFF

Set scan resume ON

Turn the split function OFF

Turn the split function ON

Select 10 Hz (or 1 Hz) tuning step

Select 100 Hz tuning step

Select 1 kHz tuning step

Select 5 kHz tuning step

Select 9 kHz tuning step

Select 10 kHz tuning step

—

Set/read attenuator.
( 0=OFF, 20=ON (20 dB))

Announce with voice synthesizer

( 00=all data 01=frequency and

S-meter; 02=receive mode)

Command Sub command

Description

[AF] level setting
(0=max. CCW to 255=max. CW)

[RF] level setting
(0=max. CCW to 255=11 o'clock)

[SQL] level setting
(0=11 o'clock to 255=max. CW)

NR level setting
(0=0% to 255=100%)

Inside [PBT] setting (0= max. CCW,
128=center, 255=max. CW)

Outside [PBT] setting (0= max.
CCW, 128=center, 255=max. CW)

CW Pitch setting (0=300 Hz to
255=900 Hz (5 Hz steps))

RF power setting
(0=minimum to 255=100%)

MIC gain setting
(0=0% to 255=100%)

Key speed level setting
(0=6 wpm to 255=60 wpm)

[MNF] setting (0=max. CCW,
128=center, 255=max. CW)

COMP level setting
(0=0 to 255=10)

Break-IN delay setting
(0=2.0 d to 255=13.0 d)

NB level setting
(0=0% to 255=100%)

VOX gain setting
(0=0% to 255=100%)

Anti VOX gain setting
(0=0% to 255=100%)

Read squelch condition

Read S-meter level

Read RF power meter

Read SWR meter

Read ALC meter

Preamp (0=OFF, 1=ON)

AGC selection
(0=OFF, 1=Fast, 2=Slow.)

Noise blanker (0=OFF, 1=ON)

Noise reduction (0=OFF, 1=ON)

Auto notch (0=OFF, 1=ON)

Speech compressor
(0=OFF, 1=ON)

VOX function (0=OFF, 1=ON)

Break-IN function (0=OFF, 1=semi
BK-IN, 2=full BK-IN)

Manual notch (0=OFF, 1=ON)

Twin peak filter (0=OFF, 1=ON)

Dial lock function (0=OFF, 1=ON)

Read the transceiver ID

Set/read memory contents

An additional code, 0001−0201
(0200=P1, 0201=P2), must be added
to specify the memory channel.

Set/read band stacking register
contents (see p. 91 for details)

Set/read the selected filter width

( SSB, CW, RTTY: 0=50 Hz

to 40/31=3600/2700 Hz;
AM: 0=200 Hz to 39=8 kHz)

0301

Set/read RF power setting
(0=minimum to 255=100%)

0302

Set/read MIC gain setting
(0=0% to 255=100%)

CONTROL COMMAND

Содержание IC-7200









































































































Результаты поиска

Содержание IC-7200

Отзывы:

Похожие инструкции для IC-7200

Бренды по названию

Популярные бренды

Icom IC-7200, Инструкция по эксплуатации

Результаты поиска

Содержание IC-7200

Отзывы:

Похожие инструкции для IC-7200

Бренды по названию

Популярные бренды