background image

28

We Think of Customer Satisfactio

n

 Electrical Connection - 

Junction Box Type

Usually an electrical permit and services of a licensed electrician are required.

The maximum allowable voltage variation is ±10 percent of the nameplate

   rating.

On single phase models, the green/yellow lead must be connected to the 

   neutral conductor of the power source. 

NOTICE! Miswiring may result 

   in damage to the icemaker.

The opening for the power supply connection is 7/8" DIA to fit a 1/2" trade size

   conduit.

ELECTRICAL CONNECTION

THIS UNIT MUST BE GROUNDED

Failure to properly ground or wire this unit could
result in death, serious injury, or severe damage 
to the icemaker.
The white lead must be connected to the netural 
of the power source.
See diagram below.

 Electrical connection must be hard-wired and must meet national, state, 

  and local electrical code requirements. Failure to meet these code requirements  
   could result in death, electric shock, serious injury, fire, or damage.

The icemaker requires an independent power supply of proper

   capacity. See the nameplate for electrical specifications. 
   Failure to use an independent power supply of proper capacity can result
   in a tripped breaker, blown fuse, damage to existing wiring, or component
   failure. This could lead to heat generation or fire.

THE ICEMAKER MUST BE GROUNDED.

 

Failure to properly ground 

   the icemaker could result in death or serious injury.

Electrical connection must be made in accordance with the instructions

   on the "WARNING" tag.

Содержание IM-0350-AC













































Отзывы: