Icar RPC 8BGA, Полное руководство

Страница: 41 / 86

ICAR PQS rev8 may18
41 / 86
M05 – MASTER / SLAVE Psw (M15) UoM Default Range
P05.01 Master-Slave function Usr OFF
OFF
COM1
COM2
P05.02 Device role Usr Master
Master
Slave01
Slave02
Slave03
…
Slave08
P05.03 Slave 1 enable Usr OFF OFF-ON
P05.04 Slave 2 enable Usr OFF OFF-ON
P05.05 Slave 3 enable Usr OFF OFF-ON
P05.06 Slave 4 enable Usr OFF OFF-ON
P05.07 Slave 5 enable Usr OFF OFF-ON
P05.08 Slave 6 enable Usr OFF OFF-ON
P05.09 Slave 7 enable Usr OFF OFF-ON
P05.10 Slave 8 enable Usr OFF OFF-ON
P05.01 - Defines whether the system is used in master-slave configuration or not. OFF the system works with a single controller (normal configuration). If you
set COM1 or COM2, working in master mode and slave setting indicates which communication channel is used for communication between controllers.
P05.02 - Defines whether the current device is a master or a slave, and in this case, which is his number.
P05.03… P05.10 - Enables the operation of individual slaves.
M06 – SLAVE 01 OUTPUTS (n=1…16) Psw (M15) UoM Default Range
P06.n.01 Output OUTn function
Usr
n=1…8
Step x
See
Output function table
n=9…16
OFF
P06.n.02 Channel number x
Usr
n=1…8
x=1…8
1 – 99
n=9…16
x=1
P06.n.03 Output normal/reversed Usr NOR
NOR
REV
Note: This menu is divided into 16 sections that refer to 16 possible digital outputs OUT1…OUT16, which can be managed by the 8BGA slave 2;
OUT81..OUT08 on the base board and OUT09…OUT16 on any installed expansion modules.
P06.n.1 – Selects the functions of the selected output (see programmable outputs functions table).
P06.n.2 – Index associated with the function programmed in the previous parameter. Example: if the output function is set to Step x , and you want this output to
be energized when there is the step 10 insertion, then P04.n.02 should be set to value 10 or If the output function is set to Alarm xx , and you want this
output to be energized for alarm A31, then P04.n.02 should be set to value 31.
P06.n.3 - Sets the state of the output when the function associated with the same is inactive: NOR = output de-energized, REV = output energized.
M13 – SLAVE 08 OUTPUTS (n=1…16) Psw (M15) UoM Default Range
P13.n.01 Output OUTn function
Usr
n=1…8
Step x
See
Output function table
n=9…16
OFF
P13.n.02 Channel number x
Usr
n=1…8
x=1…8
1 – 99
n=9…16
x=1
P13.n.03 Output normal/reversed Usr NOR
NOR
REV
See above, referred to slave 08
M14- PROGRAMMABLE INPUTS (INPn, n=1…8) Psw (M15) UoM Default Range
P14.n.01 INPn input function Adv OFF (see Input functions table)
P14.n.02 Function index (x) Adv OFF OFF / 1…99
P14.n.03 Contact type Adv NO NO/NC
P14.n.04 Delay ON Adv s 0.05 0.00-600.00
P14.n.05 Delay OFF Adv s 0.05 0.00-600.00
Note: This menu is divided into 8 sections that refer to 8 possible digital inputs
P14.n.01 – Selects the functions of the selected input (see chapter 22. Porgrammable inputs functions table ).
P14.n.02 – Index associated with the function programmed in the previous parameter. Example: If the input function is set to Cxx commands menu execution ,
and you want this input to perform command C.07 in the commands menu, P14.n.02 should be set to value 7.
P14.n.03 – Select type of contact: NO (Normally Open) or NC (Normally Closed).
P14.n.04 – Contact closing delay for selected input.
P14.n.05 – Contact opening delay for selected input.
M15 – PASSWORD UoM Default Range
P15.01 Enable password OFF OFF-ON
P15.02 User level password 1000 0-9999
P15.03 Advanced level password 2000(*) 0-9999