manualshive.com logo in svg

iC-Haus iC-PVS, Руководство пользователя, Страница: 27 / 51

Поделиться
Скачать
iC-Haus iC-PVS Скачать руководство пользователя страница 27

preliminary 

preliminary 

iC-PVS

LINEAR/OFF-AXIS
BATTERY-BUFFERED ABSOLUTE POSITION HALL SENSOR

Rev A2, Page 27/51

PCR_ADI(7:0)

Addr. 0x02; bit 7:0

reset:

PCR_ADI(15:8)

Addr. 0x03; bit 7:0

0x0000

Code

Period Counts per Revolution

0x0000

1

0x0001

2

0x0002

3

. . .

code +1

0x00FE

255

0x00FF

256

0x...

...

0x0FFF

4095

0x...

...

0xFFFF

65536

Table 12: Period Counts per (mech.) Revolution

By way of example, assume a magnetic code disc with
32 magnetic periods. With PCR_ADI = 0x0019, iC-PVS

will make a revolution count every 32 periods. The syn-

chronization bits are distributed evenly over these 32
periods, i.e. the disc is divided in 8 sectors (SBL_ADI =
3).Therefore, one sector consists of 4 magnetic periods.

The encoder system therefore acts as if it was scanning

a conventional diametral magnet. By adjusting parame-
ter PCR_ADI this can be achieved for binary or decimal
number of magnetic periods per revolution.

Alternatively, the current magnetic period of the me-

chanical revolution (period counter) can be transmitted
in the serial data stream with option PCR_OUT = 1. In
this mode, 8 or 16 period counter bits are added after
the revolution counter data and output in the serial data
stream. Unused bits are filled up with zeroes. The revo-
lution, PCR and synchronization information provide the
exact position of the code disc down to 64 increments
per magnetic period.

PCR_OUT

Addr. 0x04; bit 7

reset: 0

Code

Mode

0

No output of PCR in serial data stream

1

With condition PCR_ADI > 0x0000 and PCR_ADI <
0x0100:
PCR is transmitted with 8 bits after rev. data

1

With condition PCR_ADI

≥

0x0100:

PCR is transmitted with 16 bits after rev. data

Table 13: Enable Period Counter Output

ERR_ADI: Transmission of Error Bit

Parameter WRN_ADI enables the error bit transmission
according to Table (Table 14). The error bit nERR is an
active-low status bit. When any bit in the STATUS(7:0)

register at address 0x6C is set, an error is generated by
transmitting a ’0’. Otherwise, a ’1’ is transmitted. Refer
to chapter Status Registers on page 48 for details on
the status register.

ERR_ADI

Addr. 0x04; bit 1

reset: 1

Code

Function

0

No error bit in ADI data output

1

Add error bit to ADI data output

Table 14: Transmission of Error Bit

WRN_ADI: Transmission of Warning Bit

Parameter WRN_ADI enables the warning bit transmis-
sion according to Table 15. The warning bit nWARN
is an active-low status bit signalizing an early battery
voltage warning. A warning is indicated by transmit-
ting a ’0’ when Status bit 8, BAT_WRN is set in the
STATUS(15:8) register at address 0x6D.

WRN_ADI

Addr. 0x04; bit 2

reset: 1

Code

Function

0

No warning bit in ADI data output

1

Add warning bit to ADI data output

Table 15: Transmission of Warning Bit

DIR_ADI: Code Direction Inversion

Parameter DIR_ADI allows to invert the iC-PVS count-
ing direction if required in the specific application.

DIR_ADI

Addr. 0x04; bit 3

reset: 0

Code

Direction

0

Normal

1

Inverted

Table 16: Code Direction Inversion

ERR_PDR: Error on Power Down Reset and Preset

ERR_PDR allows to classify the PDR, PRESET and
REBOOT status bits as errors. In that case the error
bit in the serial data stream is set and the output NERR
pulled low whenever any of these bits are set in the
status register STATUS(15:8).

ERR_PDR

Addr. 0x04; bit 0

reset: 0

Code

Behaviour

0

Classify Reset Event as Error - disabled

1

Classify Reset Event as Error - active

Table 17: Error on Power Down Reset and Preset

Содержание iC-PVS




















































Отзывы:

Нет отзывов