HWH 610 SERIES Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 38

background image

REPAIR STEPS

SOLUTION

DIAGRAMS

PROBLEM

MI91.2232

26JUN98

Part 1

Part 2

REFER TO MP85.5043

REFER TO MP85.5043

REFER TO MP85.5120

Touch panel has
indicator lights on
with the ignition
switch off.

There should be no +12 power to the 7" control box. Trace the brown
or yellow wire in the 3 pin UML connector to its source. The wire should
be connected to accessory or ignition power. (Accessory power is pre-
ferred.)

With the ignition
switch on:

a. The green "TRAV-
EL" light nor the
master "JACKS
DOWN" warning
light is lit.

With the ignition switch on, the brown (or yellow) wire in the 3 pin UML
connector should have +12 power. If not, trace the wire to its source.
Check any in-line fuses. If +12 power is present, check the 5 amp ACC
fuse on the 7" control box. Check that the white wire in the 3 pin UML

b. The master "JACKS
DOWN" warning
light is on. (Jacks
are all in the stored
position.)

Push the "I" button one time. A red jacks down warning light on the
touch panel should come on, indicating a jack is down. Unplug the
jack pressure switch. If the red warning light goes out, the switch is
stuck and should be replaced. If not, unplug the jacks warning switch.
If the red warning light still does not go out, unplug the 4 wire MTA
connector for the warning switches at the 7" control box. If the red
warning light goes out, the wire to the jack warning switch is shorted
to ground. If the red warning light stays on, replace the 7" control box.

If no red warning light on the touch panel comes on, check the wires
to the master warning light. If the wires are ok, replace the 7" control
box.

REFER TO MP85.5115

REFER TO MP85.5110

REFER TO MP85.5043

c. The touch panel
has indicator lights
on other than the
green "TRAVEL"
indicator.

Turn the ignition switch off then back on. If the lights do not go out,
the 7" control box or the touch panel, is the problem.

WHITE GROUND

BROWN ACC

5 AMP

10 AMP

10 AMP

5 AMP

ACC FUSE

5 AMP

10 AMP

10 AMP

YELLOW IGN
(WHEN APPLICABLE)

5 AMP

WHITE GROUND

BROWN ACC

5 AMP

10 AMP

5 AMP

10 AMP

10 AMP

(WHEN APPLICABLE)

YELLOW IGN

ACC FUSE

10 AMP

MASTER WARNING
LIGHT

POSITIVE
VOLTAGE

LF WHITE
RF RED
RR BLACK
LR GRN

JACK WARNING/
PRESSURE SWITCH
INPUTS

connector is properly grounded. Check that the modular cable is cor-
rectly plugged into the touch panel. If it is ok, the problem is the 7"
control box.

«
...
6
7
8
9
10
...
»

Содержание 610 SERIES







































Отзывы:

Нет отзывов

Похожие инструкции для 610 SERIES

Бренд: Wavetec Страницы: 17

Бренд: Calsense Страницы: 9

Smart Controller

Бренд: MaestroHome Страницы: 10

Бренд: Samson Страницы: 52

Бренд: Samson Страницы: 32

Бренд: Danfoss Страницы: 59

vlt soft starter mcd 500

Бренд: Danfoss Страницы: 95

Бренд: Danfoss Страницы: 12

Бренд: Danfoss Страницы: 33

Бренд: Danfoss Страницы: 59

Бренд: Danfoss Страницы: 16

VLT AQUA Drive FC 200

Бренд: Danfoss Страницы: 91

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 100

Бренд: Danfoss Страницы: 82

Бренд: Danfoss Страницы: 18

Бренд: Danfoss Страницы: 12

OPTYMA Plus OP-LPQM

Бренд: Danfoss Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды