HWH 610 SERIES Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 38

background image

6000# JACK HOSE AND WIRING INSTRUCTIONS

MI91.2278

25JUN98

2

3

1

3 - LOCK WASHERS

1. Install brackets and jacks using correct installation procedures. (See Installation Manual)

This jack is usually supplied with the wiring and a short hose already installed on the jack. For clearance
purposes the hose and wire may be clamped to the opposite side of the jack. Check carefully that the
hose and wire will not catch on the jack and that the jack may fold, swing vertical and swing to the front
without damage to the hose or wire.

2. Ring terminal on warning switch must be grounded directly to the frame rail.

A. Grind the frame rail clean where ring terminal will be grounded.

B. Drill 1/4" hole in frame.

C. IMPORTANT: Place internal lock washers on both sides of the terminal and under the nut.

D. Seal both sides of bolt with silicone caulking.

3. Plug packard connector into correct wire from control box. (See Installation or Operator’s Manual)

CHASSIS FRAME RAIL
NO SUBSTITUTION

«
...
19
20
21
22
23
...
»

Содержание 610 SERIES







































Отзывы:

Нет отзывов

Похожие инструкции для 610 SERIES

Бренд: Keithley Страницы: 97

Бренд: Happ Страницы: 52

Бренд: Hansen Страницы: 4

Бренд: Baccara Страницы: 16

Бренд: Farfisa Страницы: 20

Бренд: Racal Instruments Страницы: 64

Бренд: Febco Страницы: 12

Бренд: HANYOUNG NUX Страницы: 36

Бренд: HANYOUNG NUX Страницы: 4

Бренд: MADRIX Страницы: 91

Бренд: MADRIX Страницы: 36

Бренд: MADRIX Страницы: 40

Бренд: YASKAWA Страницы: 18

Бренд: Laars Страницы: 28

Бренд: Rain Bird Страницы: 4

Бренд: Rain Bird Страницы: 2

Бренд: Rain Bird Страницы: 140

WeatherSmart RSC600i

Бренд: Raindrip Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды