HWH 610 SERIES Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 38

background image

9000# JACK HOSE AND WIRING INSTRUCTIONS

MI91.2280

25JUN98

1

4

2

3

5

6

3 - LOCK WASHERS

1. Install brackets and jacks using correct installation procedures. (See Installation Manual)

2. Route hose above roller bearing, in front of pivot nut and connect to the actuator fitting.

3. Clamp hose to pivot bracket using hose clamp. Locate clamp on hose so that there is no slack in hose

when jack is folded.

4. Route warning switch wires around front of jack and wire tie to hose by hose clamp. Check that jack

can fold without damaging or stretching wires.

5. Ring terminal on warning switch must be grounded directly to the frame rail.

A. Grind frame rail clean where ring terminal will be grounded.

B. Drill 1/4" hole in frame.

C. IMPORTANT:

Place internal lock washers on both sides of terminal and under nut.

D. Seal both sides of bolt with silicone caulking.

6. Plug packard connector into correct wire from control box. (See Installation or Operator’s Manual)

CHASSIS FRAME RAIL
NO

SUBSTITUTION

ROLLER

BEARING

«
...
20
21
22
23
24
...
»

Содержание 610 SERIES







































Отзывы:

Нет отзывов

Похожие инструкции для 610 SERIES

Бренд: Lawler Страницы: 4

Minas A4 Series

Бренд: Panasonic Страницы: 5

Бренд: Campbell Страницы: 72

Бренд: Nabco Страницы: 35

Бренд: Gardigo Страницы: 6

Бренд: VAT Страницы: 14

Бренд: M-system Страницы: 13

Бренд: WAC Страницы: 5

RDS17S-ELITE1-R1

Бренд: D&R ELECTRONICS Страницы: 12

iDual A E27 iD60

Бренд: jedi LIGHTING Страницы: 23

767-4803/000-800

Бренд: WAGO Страницы: 80

Бренд: S&C Страницы: 24

Бренд: SeaLevel Страницы: 115

Бренд: SACH Страницы: 99

Optidrive Elevator

Бренд: Invertek Страницы: 5

Бренд: Techtrol Страницы: 4

Бренд: Quickie Страницы: 108

Бренд: GARDINER TECHNOLOGY Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды